CN810D(Belt)
Intelligent Automatic Edge Sealing Machine
The belt build is the one to specify when the bander sits behind a saw: the panel arrives on the track conveyor and the same sixteen cells finish the edge without a hand-fed table in front.
Overview
- Sixteen cells in the order printed on the sheet: track conveyor, high-definition wide screen, separating agent, pre-milling, heat lamp, glue pot, fast-melt tank, servo tape feed, head-and-tail trimming, rough trimming, servo fine trimming, four-head tracking, scraping, precise flat scraping, cleaning and polishing.
- Panels from 50 mm wide and 9 to 60 mm thick, with band 0.4 to 3 mm thick and 12 to 65 mm wide.
- 16 to 23 m/min on an 8,100 mm frame, 800 mm wide and 1,900 mm high, with 18 kW installed.
- The EVA pot carries a fast-melt tank, so the adhesive reaches working temperature in less time and the first panel of a shift is not scrap.
- Servo tape feed sets the band length from the screen rather than from a hand-set stop, which matters on short runs.
- Four-head tracking runs the corners, then scraping and precise flat scraping take the surplus off the panel face before the polishing head.
- The pressure beam lifts electrically, and the recipe list sits on the wide screen instead of on a row of dials.
CN810D(Belt)
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 50 mm
Stations16
Total power18 kW
Frame8,100 mm
Station sequence
Station 01 is the track conveyor and station 02 the wide screen; the sixteen cells then run from separating agent to polishing in the order printed on the sheet.
01
Track conveyor
A crawler conveyor supports the panel and drives it through every cell at constant speed.
02
High-definition wide screen
A wide touch screen with fingertip control; a mouse and keyboard can be added if the operator prefers them.
03
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
04
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
05
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
06
Glue pot
The hot-melt is melted in the pot and applied to the panel and the band in one pass, without an external melter.
07
Fast-melt glue
The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.
08
Servo tape feed
Servo-driven tape feed sets the band length from the screen, so short runs stop wasting band.
09
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
10
Rough trimming
The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.
11
Servo fine trimming
Four axes — up-down and front-back — run on servo with micron-level error; the trimming angle is set numerically on the screen, so a changeover needs no test board.
12
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
13
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
14
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Polishing
Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.
Technical data
| Model | CN810D(Belt) |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 50 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 16 |
| Control screen | High-definition wide screen |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 18 kW |
| Machine size (L × W × H) | 8100 × 800 × 1900 mm |
Values from the CN810D technical data sheet in the 2026 configuration list. The model is printed there as CN810D(Belt), and the page keeps that as written.
What the machine is built to do
- Belt infeedThe model is listed as CN810D(Belt) on the data sheet. That build takes the panel from a conveyor line, which is the version to ask for when the bander works behind a panel saw rather than as a stand-alone cell.
- Fast-melt tank on the potA second tank brings the melt up to working temperature while the pot holds it there, so a cold start costs minutes rather than a shift.
- Servo tape feedBand length is a screen value, and the feed repeats it panel after panel without an operator checking a mechanical stop.
- Four-head trackingThe tracking unit carries four motors, so both ends of the band turn the corner in one pass instead of being cut square across it.
- Double scrapingScraping runs on both faces of the edge, then the flexible scraper takes the surplus hot-melt off the panel surface.
- Eight metre frame8,100 mm long and 800 mm wide: a compact line that still carries pre-milling, two glue functions and polishing.
Other formats
CN500
Servo Heavy-Duty Laser Edge Bander
Laser bonding with no glue line, on panels from 8 mm and strips down to 40 mm.
Laser bonding8–45 mm40 mm stripsCut-outs
Read the specification
FM758JCS Ultra
Double-Layer Handle-Free Edge Bander
Thirty handle-free profiles on one machine, switched from the screen with no waiting between shapes.
30 profilesPUR readyOne-click changeQR feeding
Read the specification
FM750JC
45° Bevel and Straight Edge Bander
The 45° bevel and the straight edge finished on the same line, plus soft-forming for wrapped profiles.
45° bevelStraightSoft-formingExport standard
Read the specification
Put CN810D(Belt) against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.