CN860D
Automatic edge banding machine
Two glue stations, each with its own heat lamp and pressing group: the second application is heated and pressed again, so a band that has already cooled is not pressed cold.
Overview
- Seventeen cells in the order printed on the sheet: wide screen, separating agent, pre-milling, heat lamp 1, glue station 1, pressing group 1, heat lamp 2, glue station 2, pressing group 2, head-and-tail trimming, rough and servo fine trimming, head tracking, servo scraping, flexible flat scraping, cleaning, polishing head 1 and polishing head 2.
- Panels from 50 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
- 16 to 23 m/min on an 8,700 mm frame, 850 mm wide and 1,700 mm high, with 26.4 kW installed.
- Rough trimming and servo fine trimming share one unit, so the band is not re-clamped between the two cuts.
- Head tracking runs two high-speed motors and turns the band round the corner before the scraping heads
- Servo scraping is followed by a flexible flat scraper, which follows the panel face instead of cutting to a fixed depth.
- Two polishing heads finish the edge, which is the step that decides how the band reads against a lacquered door.
CN860D
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 50 mm
Stations17
Total power26.4 kW
Frame8,700 mm
Station sequence
Station 01 is the wide screen; the seventeen cells then run from separating agent to the second polishing head in the order printed on the sheet.
01
High-definition wide screen
A wide touch screen with fingertip control; a mouse and keyboard can be added if the operator prefers them.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
Glue applicator
The applicator melts the hot-melt and spreads it on the panel face and the band as the panel passes.
06
Pressing, first group
The first pressure group seats the band applied at the first glue station.
07
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
08
Glue applicator
The applicator melts the hot-melt and spreads it on the panel face and the band as the panel passes.
09
Pressing
High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.
10
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
11
Rough and servo fine trimming
Rough trimming takes the overhang and a servo-driven fine head finishes to the panel face at a set position.
12
Head tracking
Two heads follow the leading and trailing end of the panel, so the band is cut round the corner instead of square across it.
13
Servo scraping
A servo motor on a precision guide rail tracks the panel face; scraping depth and pressure are closed-loop, so the edge is neither over- nor under-scraped.
14
Flexible flat scraping
A sprung scraper follows the panel face instead of a fixed depth, so surplus hot-melt comes off without cutting into the board.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Polishing
Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.
17
Second polishing
A second pair of cotton wheels follows the first, for a higher sheen on the joint than one pass gives.
Technical data
| Model | CN860D |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 50 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 17 |
| Control screen | High-definition wide screen |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 26.4 kW |
| Machine size (L × W × H) | 8700 × 850 × 1700 mm |
Values from the CN860D technical data sheet in the 2026 configuration list.
What the machine is built to do
- Two glue applicationsHeat, glue, press, heat, glue, press: the second application is made on a warm band rather than a cold one, which is what a thick or veneer band needs.
- Two polishing headsThe second pair of cotton wheels follows the first, for a higher sheen than a single head gives.
- Servo fine trimmingThe fine head is positioned by servo, so the depth is a screen value and it repeats after a band change.
- Head trackingTwo high-speed motors carry the tracking head, so the corners of a thin band are turned rather than cut square.
- Flexible flat scrapingA sprung scraper follows the panel face on thin boards, where a fixed-depth scraper would mark the surface.
- 8.7 m frame850 mm wide and 1,700 mm high: a straight-line machine that fits a bay without a pit.
More from the CN series
CN500
Servo Heavy-Duty Laser Edge Bander
Laser bonding with no glue line, on panels from 8 mm and strips down to 40 mm.
Laser bonding8–45 mm40 mm stripsCut-outs
Read the specification
CN861M
Servo Narrow Edge Automatic Edge Bander
Fourteen cells for narrow stock from 40 mm: EVA furnace, fast-melt tank, servo fine trimming, four-head tracking.
14 stations40 mm narrow stockEVA furnaceFour-head tracking
Read the specification
CN300
High-Pressure Beam Rail Edge Banding Machine
Sixteen cells on a high-pressure beam rail: PUR pot, disc trimming, 35° end trimming and two polishing heads, 22 kW.
16 stationsHigh-pressure beamTwo-colour PUR22 kW
Read the specification
Put CN860D against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.