FM468JCD
45° Bevel and Straight Edge Bander
A 45° bevel and straight edge bander for handle-free doors: pre-milling, saw cutting, band grooving, fast-melt gluing and double polishing on 9,900 mm.
Overview
- Fifteen processing cells after the screen: separating agent, pre-milling, 45° saw cutting, band grooving, bevel gluing, EVA pot with fast-melt, synchronous pressing, rough trimming, integrated end trimming, fine trimming, corner rounding, scraping, cleaning and double polishing.
- The bevel and the straight edge are switched with one key and formed in one pass, so one machine covers handle-free doors, drawer fronts and cabinet doors.
- An EVA glue pot with a fast-melt tank: the melt reaches working temperature quickly and holds it through the shift.
- Straight panels 8–60 mm, bevel panels 12–40 mm; width ≥ 40 mm straight, ≥ 60 mm bevel; edge band 12–60 mm wide.
- 24 kW total, 380 V, 0.7 MPa air; frame 9,900 × 740 × 1,750 mm.
FM468JCD
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel thickness8 – 60 / 12 – 40 mm
Panel width≥ 40 / 60 mm
Processing stations15
Total power24 kW
Station sequence
Sixteen positions: the screen, then fifteen cells from the separating-agent spray to double polishing.
01
Control screen
Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
45° saw cutting
One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.
05
Band grooving
Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.
06
Bevel gluing
A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.
07
Gluing furnace
EVA glue pot; the melt is held at working temperature through the shift.
08
Fast-melt glue
The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.
09
Bevel and straight pressing
Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.
10
Rough trimming
The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.
11
Head-and-tail trimming, bevel and straight
Both formats share one end-trimming head, so the changeover does not wait for a second cut.
12
Straight and bevel fine trimming
One trimming head takes the overhang off the straight face and the bevel face, bringing both flush with the panel.
13
Corner rounding, head tracking
A high-frequency trimming motor profiles the corners at both ends, so the banded edge runs round the panel without a step.
14
Straight and bevel scraping
One scraping head serves both formats, so a changeover does not need a second setting.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM468JCD |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm straight / ≥ 60 mm bevel |
| Panel thickness | 8 – 60 mm straight / 12 – 40 mm bevel |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 60 mm |
| Pressure beam | Electric lift |
| Processing stations | 15 |
| Control screen | Control screen, per configuration |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 24 kW |
| Machine size (L × W × H) | 9900 × 740 × 1750 mm |
Values from the FM468JCD technical data sheet and the 2026 configuration list.
What the machine is built to do
- 45° cut and milled in one set-upThe square edge is cut to 45° and the flat face milled into the bevel in the same pass — no second machine, no re-fixturing.
- Pre-milling before gluingTwo cutters take the saw marks and the out-of-square edge off the panel first, so the band meets a clean face instead of bridging a ripple.
- Bevel and straight on one bedThe same line finishes the 45° mitre and the square edge; the station list changes, the operating logic does not.
- Fast-melt tankThe melt reaches working temperature in less time, so the first panel of a shift is not scrap.
- Two polishing headsA second set of cotton wheels finishes the edge after the first pass, for a higher sheen on the joint.
Edge samples
More from the 4 series
FM490G
Servo Narrow-Panel Edge Bander
Forty-millimetre strips, 9–60 mm thick, at 16–23 m/min — with servo control on the stations that decide the finish.
16 processing cells≥ 40 mm width9 – 60 mm thick16 – 23 m/min
Read the specification
FM465
Straight Edge Bander
Nine stations on a 5,300 mm bed, 9 to 60 mm panels and no pre-milling: a straight bander for shops whose saw already cuts clean.
9 stations9–60 mm16–23 m/min5.3 m bed
Read the specification
FM465J
Straight Edge Bander
Eleven stations on a 6,400 mm bed, adding pre-milling and flat scraping to a straight edge train for 9 to 60 mm panels.
11 stationsPre-millingFlat scraping6.4 m bed
Read the specification
Put FM468JCD against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.