Name: FM708JA Servo Narrow-Panel Edge Bander with Servo Stations
Brand: CNSK
SKU: FM708JA Servo

Overview

Sixteen numbered cells: 21.5-inch industrial computer, separating agent, pre-milling, heat lamp 1, glue applicator 1, pressing group 1, heat lamp 2, glue applicator 2, pressing group 2, head-and-tail trimming, rough and fine trimming, head tracking, scraping, flexible flat scraping, cleaning and double polishing.
Servo drive on part of the station set, which is what separates this build from the standard FM708JA: the stations that have to hold a position repeat it after a recipe change instead of being re-set by hand.
Panels from 50 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
16 to 23 m/min, 8,700 mm frame, 850 mm wide, 1,700 mm high, 26 kW installed against 21.5 kW for the standard build.
Two heat lamps and two glue applicators, each with its own pressing group, so the band is pressed twice on a warm face.
A flexible flat scraper follows the panel face rather than a fixed depth, so surplus hot-melt comes off a thin board without cutting into it.
Head tracking before the scraping heads, then cleaning and two polishing units.

FM708JA Servo CNSK · Dongguan

Feed rate16 – 23 m/min

Panel width≥ 50 mm

Stations16

Total power26 kW

Servo stationsPart of the set

Station sequence

Station 01 is the 21.5-inch industrial computer; sixteen numbered cells run from separating agent to double polishing. Servo drive is fitted to part of the station set, not to all of it.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

05

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

06

Pressing, first group

The first pressure group seats the band applied at the first glue station.

07

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

08

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

09

Pressing, second group

A second pressure group follows the second glue station, for the band applied there.

10

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

11

Rough and fine trimming

Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.

12

Head tracking

Two heads follow the leading and trailing end of the panel, so the band is cut round the corner instead of square across it.

13

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

14

Flexible flat scraping

A sprung scraper follows the panel face instead of a fixed depth, so surplus hot-melt comes off without cutting into the board.

15

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

16

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Technical data

Model	FM708JA Servo
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	16
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	26 kW
Machine size (L × W × H)	8700 × 850 × 1700 mm

Values from the FM708JA servo technical data sheet in the 2026 configuration list. Servo drive is fitted to part of the station set; the station count and the frame are the same as the standard FM708JA.

What the machine is built to do

Servo on part of the lineThe buyer who needs repeatability on a narrow strip orders this build; the stations that carry servo are the ones that position, not the ones that only turn.
21.5-inch industrial computerThe recipe list and the station settings sit on one large screen, so a change of band or thickness is recalled rather than dialled in.
Two glue applicators, two pressesHeat, glue, press, heat, glue, press: the second application is not run at the setting of the first.
Flexible flat scrapingA sprung scraper follows the face of a thin panel, where a fixed-depth scraper would mark it.
Narrow geometryA 50 mm minimum panel width with a 12 to 65 mm band: drawer fronts, shelf strips and narrow stiles.
Same 8.7 m footprintThe servo build keeps the frame of the standard machine, so a bay does not have to be rebuilt to take it.