Name: FM710YC Full-Bevel and Radius Bander
Brand: CNSK
SKU: FM710YC

Overview

Fifteen numbered cells: 21.5-inch industrial computer, separating agent, servo pre-milling, EVA gluing furnace, edge band grooving, heat lamp, pressing, intelligent pressing, lower trimming, trimming, end trimming, scraping, precise flat scraping, cleaning and polishing.
One head does the shaping: the servo pre-milling spindle is what cuts the 45° bevel, the arc and the oblique arc, so this frame carries a single cutter instead of the pre-milling plus shape cutter pair used on the longer builds.
The shortest frame in the group at 6,960 mm, 950 mm wide and 1,850 mm high, with 20 kW installed and a 2,600 kg working weight.
Panels from 120 mm wide and 18 to 25 mm thick, band 0.8 to 1.0 mm thick and 30 to 65 mm wide, at a single 12 m/min feed.
The glue is EVA, melted in the furnace on the machine: the bond is made from the panel face and the band in one pass, and the furnace runs to working temperature through the shift.
Grooving runs before the heat lamp: the band is given a channel on its inner face, so it bends into the shaped corner instead of splitting along it.
Intelligent pressing reads the profile and sets its own pressure, and lower trimming reaches the underside that a single top head cannot.

FM710YC CNSK · Dongguan

Feed rate12 m/min

Panel width≥ 120 mm

Stations15

Total power20 kW

Frame6,960 mm

Station sequence

Station 01 is the 21.5-inch industrial computer; fifteen numbered cells run from separating agent to polishing. The servo pre-milling head at station 03 cuts the 45° bevel, the arc and the oblique arc, and this build carries no second shape cutter.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Servo pre-milling

A servo-controlled 9 kW spindle cuts the 45° bevel, the arc and the oblique arc straight on the shaped edge, so one head covers the formats this frame is bought for.

04

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

05

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

06

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

07

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

08

Intelligent pressing

The pressing unit reads the band and the panel profile and sets its own pressure, so a shallow recess and a deep groove are pressed with different authority.

09

Lower trimming

The lower trim head takes the band down to the underside of the profiled panel, where the upper head cannot reach.

10

Trimming

The trim head takes the band overhang back to the panel face, on the line rather than at a second bench.

11

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

12

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

13

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

14

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

15

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM710YC
Feed rate	12 m/min
Panel width	≥ 120 mm
Panel thickness	18 – 25 mm
Edge band thickness	0.8 – 1.0 mm
Edge band width	30 – 65 mm
Pressure beam	Electric lift
Processing stations	15
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	20 kW
Machine size (L × W × H)	6960 × 950 × 1850 mm

Values from the updated FM710YC technical data sheet in the 2026 configuration list. The sheet names the machine Fully Automatic Intelligent Arc Edge Banding Machine and gives the edge type as special-shaped, the beam lift as electric, and the machine weight as 2,600 kg; the page title is the short form of that name. The pre-milling station is listed as servo pre-miling on the sheet and appears here as servo pre-milling at station 03.

What the machine is built to do

Fifteen cells, shaped geometryServo pre-milling, grooving, heat, pressing, intelligent pressing, lower trimming, trimming, end trimming, scraping, flat scraping, cleaning, polishing: the sequence a recessed edge needs.
One servo head for every shapeThe 9 kW spindle is set from the screen for the 45° bevel, the arc or the oblique arc, so a change of shape is a recipe, not a cutter change.
Lower trimming as a stationA shaped edge hides its underside from the upper head, so the lower trim is fitted on the line rather than left to a bench.
Intelligent pressingPressure is set from the profile rather than from a single spring value, which is what keeps a shallow recess from being crushed.
EVA furnace on the frameThe pot is on the machine and melts EVA granulate in place: no external tank to heat, and the same setting holds through a shift.
12 m/min, single speedA shaped profile is run at one steady rate, so the bond is made at the same contact time on every panel.