Name: FM715YC Full-Bevel and Radius Bander, Pre-Milling and Cutter
Brand: CNSK
SKU: FM715YC

Overview

Sixteen numbered cells: 21.5-inch industrial computer, separating agent, pre-milling, shape cutter 1/2, EVA gluing furnace, edge band grooving, heat lamp, pressing, intelligent pressing, lower trimming, trimming, end trimming, scraping, precise flat scraping, cleaning and polishing.
Pre-milling first, then the shape cutter: the saw marks and the out-of-square edge are taken off before the profile groove is milled, so the band seats on a face cut on the machine, not on the saw.
7,990 mm frame, 950 mm wide, 1,850 mm high, 20 kW, 2,600 kg, at a single 12 m/min feed.
Panels from 120 mm wide and 18 to 25 mm thick, band 0.8 to 1.0 mm thick and 30 to 65 mm wide.
The glue is EVA, melted in the furnace on the frame; grooving cuts the channel on the band's inner face so it folds into the shaped corner.
Intelligent pressing reads the profile, and the lower trim head takes the underside of the shaped edge down to the panel face.
Precise flat scraping and a single polishing head close the sequence, with the panel face cleaned of surplus melt.

FM715YC CNSK · Dongguan

Feed rate12 m/min

Panel width≥ 120 mm

Stations16

Total power20 kW

Frame7,990 mm

Station sequence

Station 01 is the 21.5-inch industrial computer; sixteen numbered cells run from separating agent to polishing, with pre-milling at station 03 and the shape cutter at station 04.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Shape cutter 1/2

A pair of cutters mills the profile groove on the panel edge, set from the screen for the shape the order calls for.

05

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

06

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

07

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

08

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

09

Intelligent pressing

The pressing unit reads the band and the panel profile and sets its own pressure, so a shallow recess and a deep groove are pressed with different authority.

10

Lower trimming

The lower trim head takes the band down to the underside of the profiled panel, where the upper head cannot reach.

11

Trimming

The trim head takes the band overhang back to the panel face, on the line rather than at a second bench.

12

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

13

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

14

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

15

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

16

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM715YC
Feed rate	12 m/min
Panel width	≥ 120 mm
Panel thickness	18 – 25 mm
Edge band thickness	0.8 – 1.0 mm
Edge band width	30 – 65 mm
Pressure beam	Electric lift
Processing stations	16
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	20 kW
Machine size (L × W × H)	7990 × 950 × 1850 mm

Values from the FM715YC technical data sheet in the 2026 configuration list. The sheet names the machine Fully Automatic Intelligent Arc Edge Banding Machine and gives the edge type as special-shaped and the machine weight as 2,600 kg; the page title is the short form of that name.

What the machine is built to do

Pre-milling on a shaped lineThe face the band seats on is re-cut on the machine, which is what stops a shaped wrap from showing a line at the top of the profile.
Shape cutter before the grooveThe profile groove is milled after the face is clean, so the cutter is not following a ripple left by the saw.
Intelligent pressingPressure is set from the profile instead of a single spring value, so a shallow recess and a deep groove are both closed.
Lower trimming on the lineThe underside of a shaped edge is trimmed at a station rather than at a bench, which is where a wrap usually goes wrong.
Single-speed 12 m/min feedOne steady rate keeps the contact time the same on every panel, which is what a shaped bond needs.
8 m frameThe extra length over the compact build is the pre-milling station, not a longer outfeed.