Name: FM716YC Full-Bevel and Radius Bander, Upper Tracking
Brand: CNSK
SKU: FM716YC

Overview

Seventeen numbered cells: 21.5-inch industrial computer, separating agent, pre-milling, shape cutter 1/2, gluing furnace, edge band grooving, heat lamp, pressing, intelligent pressing, lower trimming, trimming, end trimming, upper tracking, scraping, precise flat scraping, cleaning and polishing.
Upper tracking sits between end trimming and scraping: the head follows the leading and trailing end at the top of the profile, where a fixed head would cut the corner square.
8,840 mm frame, 950 mm wide, 1,850 mm high, 20 kW, 2,600 kg, single 12 m/min feed.
Panels from 120 mm wide and 18 to 25 mm thick, band 0.8 to 1.0 mm thick and 30 to 65 mm wide.
Pre-milling, shape cutter, grooving, heat and two pressing stages: the profile sequence of the shaped family, with the upper track added at the end.
Lower trimming reaches the underside of the shaped edge; upper tracking then rounds the end before the scraping head touches the band.
Precise flat scraping and polishing finish the joint, and the 21.5-inch screen holds the station settings per recipe.

FM716YC CNSK · Dongguan

Feed rate12 m/min

Panel width≥ 120 mm

Stations17

Total power20 kW

Frame8,840 mm

Station sequence

Station 01 is the 21.5-inch industrial computer; seventeen numbered cells run from separating agent to polishing. The upper tracking head is station 13.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Shape cutter 1/2

A pair of cutters mills the profile groove on the panel edge, set from the screen for the shape the order calls for.

05

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

06

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

07

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

08

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

09

Intelligent pressing

The pressing unit reads the band and the panel profile and sets its own pressure, so a shallow recess and a deep groove are pressed with different authority.

10

Lower trimming

The lower trim head takes the band down to the underside of the profiled panel, where the upper head cannot reach.

11

Trimming

The trim head takes the band overhang back to the panel face, on the line rather than at a second bench.

12

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

13

Upper tracking

The upper head follows the leading and trailing end of the panel, so the band is cut round the corner instead of square across it.

14

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

15

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

16

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

17

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM716YC
Feed rate	12 m/min
Panel width	≥ 120 mm
Panel thickness	18 – 25 mm
Edge band thickness	0.8 – 1.0 mm
Edge band width	30 – 65 mm
Pressure beam	Electric lift
Processing stations	17
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	20 kW
Machine size (L × W × H)	8840 × 950 × 1850 mm

Values from the FM716YC technical data sheet in the 2026 configuration list. The sheet names the machine Fully Automatic Intelligent Arc Edge Banding Machine and gives the edge type as special-shaped and the machine weight as 2,600 kg; the page title is the short form of that name.

What the machine is built to do

Upper tracking on a shaped lineThe end of a recessed band is cut at the top of the profile; tracking that head is what keeps the corner round on a shaped panel.
Pre-milling before the shape cutThe face is re-cut on the machine, so the profile groove is milled into clean material.
Two pressing stagesA standard press and an intelligent press follow each other, so the first seats the band and the second closes the profile.
Lower trimming at a stationThe underside is trimmed on the line, not at a bench, which is where a shaped wrap usually shows first.
Seventeen cellsOne more than the 7,990 mm build, and the extra cell is the upper tracking head.
Electric beam lift and recipe memoryA change of panel thickness is a screen setting, and the recipe returns the station positions with it.