FM725YCX

Five-Profile Arc and Bevel Edge Bander

Name: FM725YCX Five-Profile Arc and Bevel Edge Bander
Brand: CNSK
SKU: FM725YCX

Five profiles on one bed: half-round, quarter-round, 45° bevel-straight, full bevel and duck-bill. The shapes that decide a curved-door range, without a machine for each one.

Request a configuration WhatsApp

Overview Station sequence Technical data Built to do More models

Overview

Arc and profile work is usually where a factory stops being able to promise a delivery date: each radius means another tooling set, another setup, another batch of scrap while the operator finds the pressure.

This machine carries the profile set in one bed. A factory that sells curved doors, rounded islands and the duck-bill detail can run all five shapes in the same shift, on the same panel thickness, without moving the work to a second station.

FM725YCX CNSK · Dongguan

Profiles5

Arc toolingR15 · R13 · R20

Bevel45° bevel + bevel-straight

Model ladder3 / 4 / 5 processes

Station sequence

Eighteen positions, screen first: milling, 45° gluing and grooving, pressing, trimming, scraping and polishing, in the order the panel runs.

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

Servo milling shaping 1

A forward-and-reverse diamond cutter mills the quarter-round profile and doubles as the straight-edge pre-mill.

Servo milling shaping 2

A 9 kW spindle mills the other four shapes — 45° full bevel, 45° bevel-straight, half-round and duck-bill.

Servo 45° full-bevel gluing

A servo module applies glue and seats the band on inclined faces of different thickness, for a seamless bevel.

PUR gluing

A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

Servo press-fitting module

The pressing module is servo-driven and follows the contour of the shaped panel, so the band seats along the curve.

Lower rough trimming

The band on the underside is trimmed flush first, so the fine head starts from a clean edge.

Servo fine trimming

Four axes — up-down and front-back — run on servo with micron-level error; the trimming angle is set numerically on the screen, so a changeover needs no test board.

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

Servo scraping

A servo motor on a precision guide rail tracks the panel face; scraping depth and pressure are closed-loop, so the edge is neither over- nor under-scraped.

45° lower face fine trimming

The excess band is cut off the underside of the full-bevel panel, leaving the bottom face flat and smooth.

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

Servo polishing

The polishing head is servo-driven and follows the profiled contour, so the cotton wheel stays on the band instead of the panel face.

Technical data

Arc tooling set and the panel range for each profile are confirmed against your door drawings before the offer is issued.

What the machine is built to do

Five profilesHalf-round, quarter-round, 45° bevel-straight, 45° full bevel and duck-bill are all available on the same bed.
Radius toolingR15, R13 and R20 arc sets are supported, covering the curved-door range most kitchen and wardrobe programmes are built around.
A model ladder, not a compromiseThe same platform is offered at three levels — FM710YC with three processes, FM715YC with four, FM725YCX with five — so a buyer pays for the profile set they actually sell.
45° work includedThe bevel and bevel-straight formats are covered here as well, so a curved programme does not need a separate bevel line.