Name: FM726YCX Five-Profile Arc and Bevel Edge Bander, PUR
Brand: CNSK
SKU: FM726YCX

Overview

PUR is usually specified for one of two reasons: the panel is going into a wet or hot environment, or the decor is dark or high-gloss, where an EVA line slowly shows through. On a curved door both reasons apply at the bevel and at the arc, so the glue decision has to be made for the whole profile set rather than for one straight edge.

This machine takes the profile set of the FM725YCX and runs it on a no-cleaning PUR pot that switches between two colours. The 45° bevel is glued and pressed in one servo-controlled pass, the band is grooved before it goes round the corner, and the same bed carries the quarter-round, half-round and duck-bill formats a curved-door programme needs.

FM726YCX CNSK · Dongguan

Profiles5

GluingTwo-colour PUR

Feed rate5 / 8 m/min

Total power44.1 kW

Station sequence

Twenty stations behind the screen, from the separating spray to the servo polishing head, in the order the panel runs.

01

21.5-inch industrial screen

A large touch screen carries the recipe list and every station setting, with parameter changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Servo milling 1

A servo-driven diamond cutter mills the quarter-round, and also covers pre-milling on the straight edge.

04

Servo milling 2

A 9 kW spindle cuts the other four shapes: 45° full bevel, 45° bevel-straight, half-round and duck-bill.

05

Servo 45° gluing and pressing

Glue is applied and the bevel is laminated at one station under servo control, so the inclined face of each thickness is bonded in the same pass.

06

Heat lamp 1

The panel is warmed before gluing, which keeps the bond even when the shop is cold.

07

PUR gluing

A no-cleaning pot holds two PUR colours and switches between them without a solvent flush.

08

Servo tape feed

Band feed is servo-matched to the panel speed, so the band is not stretched at the start of a run.

09

Heat lamp 2

A second lamp reheats the band and the panel after grooving, so the 45° band is still soft when it reaches the press.

10

Straight-edge pressing

Pressure wheels load the straight band evenly against the panel face.

11

Bevel-edge pressing

A second group loads the inclined band, so the bevel and the straight face are both held at the joint.

12

Servo press-fitting module

The module follows the contour of the shaped panel and presses along the curve rather than flat across it.

13

Lower rough trimming

The band on the underside is trimmed flush first, so the fine head starts from a clean edge.

14

Full-bevel bottom trimming

The surplus band on the underside of a 45° full-bevel panel is cut away, leaving the bottom face flat.

15

Servo fine trimming

Depth is set from the screen for each panel thickness and profile, so a format change needs no test board.

16

Head and tail trimming

The band is cut flush at the leading and trailing ends, with the trim motor on a high-frequency drive.

17

Head tracking

The tracking head profiles the corner at both ends, so the band follows the radius instead of being cut square across it.

18

Servo scraping

The scraper is positioned by servo for each thickness and shape, taking the knife marks off the band.

19

Full-bevel scraping

Surplus hot-melt is taken off the panel face and the band on the full-bevel format, so the return is flat before polishing.

20

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

21

Servo polishing

Cotton wheels on servo control finish the edge on each thickness and shape.

Technical data

Model	FM726YCX
Total power	44.1 kW
Voltage	380 V
Air pressure	0.7 MPa
Electric lift	Motorized
Feed speed	5 m/min · 8 m/min on 45° bevel-straight
Panel width	≥ 120 mm
Machine size (L × W × H)	9350 × 950 × 1700 mm
Machine weight	3600 kg
Panel thickness · 45° full bevel	9 – 22 mm
Panel thickness · 45° bevel-straight	9 – 25 mm
Panel thickness · 1/4 arc	18 – 22 mm
Panel thickness · 1/2 arc	18 – 22 mm
Panel thickness · duck-bill	18 – 22 mm
Edge band thickness · 45° full bevel	0.8 – 1.0 mm
Edge band thickness · 45° bevel-straight	0.8 – 1.0 mm
Edge band thickness · 1/4 arc	0.6 – 0.8 mm
Edge band thickness · 1/2 arc	0.6 – 0.8 mm
Edge band thickness · duck-bill	0.6 – 0.8 mm
Edge band width · 45° full bevel	30 mm
Edge band width · 45° bevel-straight	30 mm
Edge band width · 1/4 arc	40 mm
Edge band width · 1/2 arc	40 mm
Edge band width · duck-bill	40 mm

Figures are taken from the FM726YCX PUR technical data sheet in the 2026 configuration list. Panel thickness, edge band thickness and edge band width are stated per profile; the tooling set for each profile is confirmed against your door drawings before the offer is issued.

What the machine is built to do

Five profiles on one bed45° full bevel, 45° bevel-straight, quarter-round, half-round and duck-bill are all available on the same bed; the recipe decides which units run.
Two-colour PUR, no cleaningA no-cleaning PUR pot holds two adhesive colours and switches between them without a solvent flush, so a colour change is a recipe change rather than a teardown.
45° glued and pressed in one passThe bevel is glued and laminated at the same station under servo control, which is what keeps a full-bevel joint invisible on a dark panel.
Grooving before the cornerThe band is grooved on its inner face before it is pressed round the corner, so the 45° return stays sharp instead of lifting.
Servo press-fitting on the profileThe pressing module follows the contour of the shaped panel, so the band seats along the curve instead of being loaded flat across it.