Name: FM759GJC Soft-Forming Edge Bander with Track Conveyor
Brand: CNSK
SKU: FM759GJC

Overview

Twenty numbered cells: 21.5-inch industrial computer, pre-milling, servo forming cutter 1/2, servo forming cutter 3/4, bottom chamfer, panel preheating, gluing on the board surface, servo tape feed with notch and band gluing, fast-melt glue, transmission pressing, baking lamps 1 to 4, heat gun, seventeen-group servo forming and pressing, rough trimming, four-speed dual-track head-and-tail trimming, fine trimming, scraping, notch trimming, cleaning and servo polishing.
A track conveyor runs under the panel from the infeed; it is a frame feature and does not take a station number, so the screen is station 01 and the sequence has twenty numbered cells.
Two servo cutter pairs mill the profile on both faces of the band, and bottom chamfer sets the lower edge to the notch contour before gluing.
Gluing on the board surface, servo tape feed and fast-melt glue feed a transmission pressing section, so the band is laid and pressed as a continuous web.
The track conveyor keeps the panel from drifting on a long wrap, which is the difference between a profile that closes and one that rides up at the corner.
9,985 mm frame, 1,200 mm wide, 1,850 mm high, 52 kW, 4,600 kg, at a single 8 m/min feed.
Panels from 120 mm wide and 18 to 25 mm thick, band 0.5 to 0.7 mm thick and 30 to 65 mm wide.

FM759GJC CNSK · Dongguan

Feed rate8 m/min

Panel width≥ 120 mm

Stations20

Total power52 kW

ConveyorTrack type

Station sequence

Station 01 is the 21.5-inch industrial computer. The track conveyor is a frame feature and is not counted as a station, so the sequence has twenty numbered cells, from pre-milling to servo polishing.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

03

Servo forming cutter 1/2

Two 7 kW spindles mill the profile grooves — J, C, W, arc, half-pass, ox-horn and drop shapes among more than twenty-five — with the shape called from the screen.

04

Servo forming cutter 3/4

A second pair of servo spindles mills the opposite face of the profile, so a wrap is cut on both sides of the band in one pass.

05

Bottom chamfer

The lower edge is chamfered to the notch contour, so the band folds under the panel instead of lifting at the corner.

06

Panel preheating

The panel and the band are brought up to temperature before the glue station, so the bond holds on a cold floor and in winter.

07

Gluing on the board surface

Adhesive is applied directly to the panel face, which is what a soft-formed or recessed profile needs before the band is laid into it.

08

Servo tape feed and notch gluing

Tape feed is servo-matched to the panel speed; glue is applied in the notch and on the band at separate points.

09

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

10

Transmission pressing

A driven pressing section carries the panel through the forming zone at constant speed, so the band is loaded for its full contact length.

11

Baking lamps 1–4

Four lamps heat the band along the forming section, so it stays soft across a long profile and a cold shop floor.

12

Heat gun

Hot air softens the band before it enters the forming press, so a tight radius folds without a white stress line.

13

Seventeen-group forming press

Seventeen pressure components load the band along every curve and corner of the profile, so the wrap closes without a second pass.

14

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

15

Four-speed automatic dual-track head-and-tail trimming

Two tracks run the ends and the speed is switched in four steps, so a pair of panels is trimmed without dropping the feed rate.

16

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

17

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

18

Notch trimming

The notch edges are fine-trimmed after pressing, so the profile reads clean and the panel face stays flat.

19

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

20

Servo polishing

The polishing head is servo-driven and follows the profiled contour, so the cotton wheel stays on the band instead of the panel face.

Technical data

Model	FM759GJC
Feed rate	8 m/min
Panel width	≥ 120 mm
Panel thickness	18 – 25 mm
Edge band thickness	0.5 – 0.7 mm
Edge band width	30 – 65 mm
Pressure beam	Electric lift
Processing stations	20
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	52 kW
Machine size (L × W × H)	9985 × 1200 × 1850 mm

Values from the FM759GJC technical data sheet in the 2026 configuration list. The sheet lists twenty-one positions, of which the second is the track conveyor; that position is a frame feature, so the station count is twenty. The sheet also gives the edge type as special-shaped and the machine weight as 4,600 kg.

What the machine is built to do

Track conveyor on the infeedA crawler supports the panel and drives it at constant speed through every cell, so the contact time under the lamps and the press does not vary.
Two servo cutter pairsThe profile is milled on both faces of the band, so a wrap is cut rather than folded onto a single groove.
Bottom chamferThe lower edge is chamfered to the notch contour, which is the detail that stops a wrap lifting at the corner.
Seventeen forming groupsPressure along the whole profile, with four baking lamps and a heat gun keeping the band soft into the press.
Transmission pressingA driven pressing section carries the panel through the forming zone, so the band is loaded for its full contact length.
8 m/min, 52 kWA production rate for a soft-forming line, with the track conveyor holding the wrap steady at it.