Name: FM759JCS High-Output Soft-Forming Edge Bander
Brand: CNSK
SKU: FM759JCS

Overview

Twenty-five numbered cells: 21.5-inch industrial computer, separating agent, servo forming cutter 1/2, servo forming cutter 3/4, bottom chamfer, gluing furnace, fast-melt glue, forming and pressing 1, notch trimming, rough trimming 1, pre-milling, panel preheating, two-colour PUR no-cleaning pot, heat gun, servo tape feed with notch and band gluing, transmission pressing, baking lamps 1 to 4, seventeen-group servo forming and pressing, rough trimming 2, four-speed dual-track head-and-tail trimming, fine trimming, scraping, notch trimming, cleaning and servo polishing.
A track conveyor runs under the panel at the infeed; it is a frame feature and does not take a station number, so the screen is station 01 and the sequence has twenty-five numbered cells.
Two servo cutter pairs, bottom chamfer and a gluing sequence that runs the panel face, the notch and the band before the transmission press.
EVA furnace with a fast-melt tank and a two-colour PUR pot are both fitted, with a heat gun ahead of the servo tape feed.
11,300 mm frame, 1,200 mm wide, 1,850 mm high, 83 kW, 6,000 kg, at a single 6 m/min feed: a heavy line run slowly for the profile.
Panels from 120 mm wide and 18 to 22 mm thick, band 0.6 to 0.65 mm thick and 30 to 65 mm wide.
The station order follows the data sheet as printed, with forming and pressing 1 at station 08 and the second notch trim at station 23.

FM759JCS CNSK · Dongguan

Feed rate6 m/min

Panel width≥ 120 mm

Stations25

Total power83 kW

Forming groups17

Station sequence

Station 01 is the 21.5-inch industrial computer. The track conveyor at the infeed is a frame feature and is not counted as a station, so the sequence has twenty-five numbered cells. The order is the dual-coating soft-forming sequence printed on the sheet: forming cutter 1/2, forming cutter 3/4 and the bottom chamfer come before the furnace, and the notch trim at station 08 and pre-milling at station 10 sit inside the forming section rather than at either end.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Servo forming cutter 1/2

Two 7 kW spindles mill the profile grooves — J, C, W, arc, half-pass, ox-horn and drop shapes among more than twenty-five — with the shape called from the screen.

04

Servo forming cutter 3/4

A second pair of servo spindles mills the opposite face of the profile, so a wrap is cut on both sides of the band in one pass.

05

Bottom chamfer

The lower edge is chamfered to the notch contour, so the band folds under the panel instead of lifting at the corner.

06

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

07

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

08

Forming and pressing 1

The first laminating group follows the contour of the profiled panel and seats the first band layer along the groove.

09

Notch trimming

The notch edges are fine-trimmed after pressing, so the profile reads clean and the panel face stays flat.

10

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

11

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

12

Panel preheating

The panel and the band are brought up to temperature before the glue station, so the bond holds on a cold floor and in winter.

13

Two-colour PUR no-cleaning pot

The pot holds two PUR colours and switches between them without a solvent flush, and it sits outside the machine so the melt is kept apart from the EVA furnace.

14

Heat gun

Hot air softens the band before it enters the forming press, so a tight radius folds without a white stress line.

15

Servo tape feed and notch gluing

Tape feed is servo-matched to the panel speed; glue is applied in the notch and on the band at separate points.

16

Transmission pressing

A driven pressing section carries the panel through the forming zone at constant speed, so the band is loaded for its full contact length.

17

Baking lamps 1–4

Four lamps heat the band along the forming section, so it stays soft across a long profile and a cold shop floor.

18

Seventeen-group forming press

Seventeen pressure components load the band along every curve and corner of the profile, so the wrap closes without a second pass.

19

Rough trimming 2

A second rough-trim pair takes the band down to the panel faces after the forming section, with four depth settings.

20

Four-speed automatic dual-track head-and-tail trimming

Two tracks run the ends and the speed is switched in four steps, so a pair of panels is trimmed without dropping the feed rate.

21

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

22

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

23

Notch trimming

The notch edges are fine-trimmed after pressing, so the profile reads clean and the panel face stays flat.

24

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

25

Servo polishing

The polishing head is servo-driven and follows the profiled contour, so the cotton wheel stays on the band instead of the panel face.

Technical data

Model	FM759JCS
Feed rate	6 m/min
Panel width	≥ 120 mm
Panel thickness	18 – 22 mm
Edge band thickness	0.6 – 0.65 mm
Edge band width	30 – 65 mm
Pressure beam	Electric lift
Processing stations	25
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	83 kW
Machine size (L × W × H)	11300 × 1200 × 1850 mm

Values from the FM759JCS technical data sheet in the 2026 configuration list. The sheet lists twenty-six positions, of which the first is the track conveyor; that position is a frame feature, so the station count is twenty-five. The sheet also gives the edge type as special-shaped and the machine weight as 6,000 kg.

What the machine is built to do

83 kW installedThe heaviest build in the forming range: two cutter pairs, a pot, a fast-melt tank and seventeen pressing groups on one line.
Two servo cutter pairsThe profile is milled on both faces of the band, so a wrap is cut rather than folded onto a single groove.
PUR and EVA togetherThe two-colour no-cleaning pot and the EVA furnace are both on the frame, so the adhesive follows the order rather than the machine.
Seventeen forming groupsPressure along the whole profile, with four baking lamps and a heat gun keeping the band soft into the press.
Notch trimming twiceThe notch is trimmed before the rough trim and again after scraping, so the profile reads clean at the notch.
6 m/minA slow line on purpose: a 0.6 mm band wrapped round a profile needs its time under the lamps and under the press.