FM930 LASER

Intelligent laser crawler edge banding machine

Name: FM930 LASER Intelligent laser crawler edge banding machine
Brand: CNSK
SKU: FM930 LASER

Three bonding paths on one crawler bed: an EVA furnace, a two-colour PUR pot and a laser unit, so the machine can be quoted against whichever band the job specifies.

Request a configuration WhatsApp

Overview Station sequence Technical data Built to do More models

FM930 LASER — Intelligent laser crawler edge banding machine

Overview

Nineteen cells in the order printed on the sheet: 21.5-inch industrial computer, track conveyor, heavy-duty one-piece bed rail, separating agent, pre-milling, gluing furnace, two-colour PUR no-cleaning pot, pressing, laser operating system, laser cooling system, swing-type cutter and tape feed, swing-type pressing, double-track head-and-tail alignment, rough and fine trimming, four-head tracking, double scraping, precise flat scraping, cleaning and double polishing.
An EVA gluing furnace at station 06 and a two-colour PUR pot at station 07 sit ahead of the laser unit, so EVA, PUR and laser band all run on the same bed.
The laser operating system and its cooling unit follow the pressing position, which is what lets the head run continuously.
Panels from 60 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
16 to 26 m/min on a 10,650 mm frame, 850 mm wide and 1,800 mm high, with 22.5 kW installed.
The bed is 150 mm longer and 100 mm wider than the FM900 LASER, and 5.5 kW lighter on installed load.
Swing-type pressing, double-track end trimming and double polishing close the line.

FM930 LASER CNSK · Dongguan

Feed rate16 – 26 m/min

Panel width≥ 60 mm

Stations19

Total power22.5 kW

Frame10,650 mm

Station sequence

Station 01 is the 21.5-inch computer and station 02 the track conveyor; the EVA furnace is station 06 and the laser unit station 09, in the order printed on the sheet.

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

Track conveyor

A crawler conveyor supports the panel and drives it through every cell at constant speed.

Heavy-duty one-piece bed rail

A one-piece guide-rail beam carries a heavy steel pressure beam; the section is sized for the load a 45° cut puts through the bed.

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

EVA gluing furnace

The furnace melts EVA granulate and applies it to the panel face and the band in one pass; the pot sits on the machine, with no external tank and no cleaning solvent.

Two-colour PUR no-cleaning pot

The pot holds two PUR colours and switches between them without a solvent flush, and it sits outside the machine so the melt is kept apart from the EVA furnace.

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

Laser operating system

The laser source, its power curve and the band feed are run from one controller, so a change of band is a recipe change rather than a re-setup.

Laser cooling system

A closed cooling circuit holds the laser at working temperature, so the bond stays even across a long shift.

Swing-type cutter and tape feed

The cutter swings to the band angle and the tape feed follows it, so a change of band width is a setting rather than a tool change.

Swing-type pressing

The pressure roller swings on an arc and cushions the load at the joint instead of hitting the band flat.

Double-track head-and-tail alignment

Two guide tracks move the end-trimming heads, so both ends are aligned and cut without dropping the feed speed.

Rough and fine trimming

Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.

Four-head corner tracking

Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.

Double-edge scraping

Scraping on both edges of the run, for trim marks and surplus glue on either face.

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Technical data

Model	FM930 LASER
Feed rate	16 – 26 m/min
Panel width	≥ 60 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	19
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	22.5 kW
Machine size (L × W × H)	10650 × 850 × 1800 mm

Values from the Laser930 technical data sheet in the 2026 configuration list. The data sheet prints the model as Laser930; the page carries FM930 LASER as the model designation used on this site, and the equipment name is the sheet's own line.

What the machine is built to do

EVA, PUR and laser in one lineThree bonding paths in one station list: the machine is specified against the band, not the other way round.
Cooled laser headA dedicated cooling system follows the laser unit, so the head is not limited to short cycles.
Swing pressingThe pressure roller swings on an arc and cushions the load at the joint instead of hitting the band flat.
Double-track end trimmingTwo tracks move the end heads, so both ends are aligned and cut at full feed.
Double polishingTwo polishing positions finish the edge, which is where a laser joint reads against a lacquered panel.
Ten and a half metre frame10,650 mm long, 850 mm wide, 1,800 mm high: the longer of the two crawler laser frames.