Name: FM368CD 45° Bevel and Straight Edge Bander
Brand: CNSK
SKU: FM368CD

Overview

Eleven processing cells covering both formats: 45° saw cutting, bevel gluing, grooving, straight gluing, synchronous pressing, bevel fine trimming, integrated end trimming, straight fine trimming, scraping and two polishing heads.
Bevel and straight are finished on the same line, so a mixed order does not need a second machine or an outsourced bevel station.
Straight panels 9–60 mm; bevel panels 15–40 mm; width ≥ 60 mm straight, ≥ 80 mm bevel.
The finishing heads are separate — the bevel setting is left alone when the straight edge runs.
18 kW total, 380 V, 0.7 MPa air; frame at 7,250 mm.

FM368CD CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 / 15 – 40 mm

Panel width≥ 60 / 80 mm

Processing stations11

Total power18 kW

Station sequence

Set the job on the screen; the panel then passes eleven cells, with one trimming head for the bevel and one for the straight edge.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

45° saw cutting

One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.

03

Bevel gluing

A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.

04

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

05

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

06

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

07

Bevel fine trimming

Special trim knives bring the bevel band flush to the upper and lower faces; the bevel and straight heads are independent.

08

Head-and-tail trimming, bevel and straight

Both formats share one end-trimming head, so the changeover does not wait for a second cut.

09

Straight fine trimming

The straight edge has its own finishing head, so the bevel setting is left untouched when the format changes.

10

Straight and bevel scraping

One scraping head serves both formats, so a changeover does not need a second setting.

11

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

12

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM368CD
Feed rate	16 – 23 m/min
Panel width	≥ 60 mm straight / ≥ 80 mm bevel
Panel thickness	9 – 60 mm straight / 15 – 40 mm bevel
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	11
Control screen	Numeric panel or industrial touch screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	18 kW
Machine size (L × W × H)	7250 × 800 × 1750 mm

Values from the FM368CD technical data sheet and the 2026 configuration list.

What the machine is built to do

45° cut and milled in one set-upThe square edge is cut to 45° and the flat face milled into the bevel in the same pass — no second machine, no re-fixturing.
Bevel and straight on one bedThe same line finishes the 45° mitre and the square edge; the station list changes, the operating logic does not.
Band groovingGrooves cut on the inner face of the band let it bend and press cleanly around a 45° corner.
Synchronous bevel pressingPressure wheels load the bevel and the straight face together, so both bonds are made in one pass.
Electric beam liftThe pressure beam is set from the screen rather than by hand crank, so a mixed batch of thicknesses needs no reset between panels.