Name: FM368CX 45° Full-Bevel and Bevel-Straight Edge Bander
Brand: CNSK
SKU: FM368CX

Overview

Thirteen processing cells, from servo milling and a servo 45° gluing module through to bevel trimming, scraping and polishing.
Two formats — 45° full bevel and 45° bevel-straight — switched from the screen, not by changing tooling.
The 21.5-inch industrial screen carries the recipe list; the pressure beam height is set from it as well.
PUR pot with two adhesive colours and no cleaning cycle, next to the heat lamps that pre-heat the board.
Two feed speeds: 8 m/min and 5 m/min, chosen by format. 20 kW total, 380 V.

FM368CX CNSK · Dongguan

Feed rate8 / 5 m/min

Panel thickness9 – 60 mm

Panel width≥ 40 mm

Processing stations13

Total power20 kW

Station sequence

Two heat lamps sit on the line: one ahead of the PUR pot, one ahead of the grooving and pressing group.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Servo milling

Servo-controlled diamond cutters mill both formats to micron precision, and switch between them from the screen.

03

Servo 45° full-bevel gluing

A servo module applies glue and seats the band on inclined faces of different thickness, for a seamless bevel.

04

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

05

PUR gluing

A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.

06

Servo band grooving

Servo-positioned grooving on the inner face of the band, for a 45° bend with a crisp surface contour.

07

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

08

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

09

45° lower face fine trimming

The excess band is cut off the underside of the full-bevel panel, leaving the bottom face flat and smooth.

10

45° panel face fine trimming

The overhang on the upper and lower faces of the bevel or bevel-straight panel is cut back flush.

11

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

12

Bevel scraping

Scraping on the bevel faces removes knife marks and surplus glue on both faces of the 45° band.

13

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

14

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM368CX
Feed rate	8 m/min / 5 m/min, by format
Panel width	≥ 40 mm
Panel thickness	9 – 60 mm
Gluing	PUR, two adhesive colours (no-cleaning pot)
Pressure beam	Electric lift, set from the screen
Processing stations	13
Control screen	21.5-inch industrial touch screen
Input voltage	380 V
Air pressure	0.7 MPa
Total power	20 kW
Machine size (L × W × H)	6050 × 950 × 1700 mm

Values from the 2026 configuration list. The FM368CX technical file does not carry a parameter table; band range and tooling are confirmed on the data sheet issued with the offer.

What the machine is built to do

Servo-controlled modulesMilling, gluing, grooving and pressing are servo-positioned, so the two formats switch from the screen instead of by hand.
PUR, two glue coloursA no-cleaning PUR pot switches between two adhesive colours, for panels where EVA will not hold or the joint has to stay invisible.
21.5-inch industrial screenA large touch screen carries the recipe list and the station settings, with parameter changes shown live.
Electric beam liftThe pressure beam is set from the screen rather than by hand crank, so a mixed batch of thicknesses needs no reset between panels.