Name: FM368JAH Two-Pot Straight Edge Bander with Notching
Brand: CNSK
SKU: FM368JAH

Overview

Twelve processing cells: pre-milling, two glue groups with fast-melt, two pressing groups, head-and-tail trimming, rough and fine trimming, scraping, double polishing and notching.
Notching after polishing means a notched profile panel does not go back through a second machine.
Two glue pots switched with one key, for a batch that changes adhesive between the band types.
8,000 mm bed, 9–60 mm panels, 16–23 m/min.
26 kW total, 380 V, 0.7 MPa air.

FM368JAH CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 mm

Panel width≥ 50 mm

Processing stations12

Total power26 kW

Station sequence

The first glue group carries its fast-melt tank; the second pot and its tank follow the first pressing group.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

03

Gluing furnace with fast-melt tank

EVA pot with a fast-melt tank, so the adhesive reaches working temperature quickly and holds it through the shift.

04

Pressing, first group

The first pressure group seats the band applied at the first glue station.

05

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

06

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

07

Pressing, second group

A second pressure group follows the second glue station, for the band applied there.

08

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

09

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

10

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

11

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

12

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

13

Notching

A slotting unit cuts the notches the profile needs after banding, so a notched panel does not need a second machine.

Technical data

Model	FM368JAH
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	12
Control screen	Numeric panel or industrial touch screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	26 kW
Machine size (L × W × H)	8000 × 800 × 1750 mm

Values from the FM368JAH technical data sheet and the 2026 configuration list.

What the machine is built to do

Pre-milling before gluingTwo cutters take the saw marks and the out-of-square edge off the panel first, so the band meets a clean face instead of bridging a ripple.
Fast-melt tankThe melt reaches working temperature in less time, so the first panel of a shift is not scrap.
Two polishing headsA second set of cotton wheels finishes the edge after the first pass, for a higher sheen on the joint.
Notching on the lineThe slotting unit cuts the notches a profile panel needs after banding, so the part does not come off the line for a second operation.