Name: FM368JCD 45° Bevel and Straight Edge Bander with Pre-Milling
Brand: CNSK
SKU: FM368JCD

Overview

Thirteen processing cells: 45° saw cutting, pre-milling, bevel gluing, grooving, straight gluing, synchronous pressing, bevel fine trimming, integrated end trimming, straight fine trimming, scraping, flat scraping and two polishing heads.
Flat scraping takes the surplus hot-melt off the panel face and the band before polishing, which is the step a matte or a lacquered finish notices.
Straight panels 9–60 mm; bevel panels 15–40 mm; width ≥ 60 mm straight, ≥ 80 mm bevel.
Separate fine-trimming heads for the bevel and the straight edge; one scraping head serves both.
22 kW total, 380 V, 0.7 MPa air; frame at 7,800 mm.

FM368JCD CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 / 15 – 40 mm

Panel width≥ 60 / 80 mm

Processing stations13

Total power22 kW

Station sequence

Set the job on the screen; the panel then passes thirteen cells, from the saw cut to the second polishing head.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

45° saw cutting

One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Bevel gluing

A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.

05

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

06

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

07

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

08

Bevel fine trimming

Special trim knives bring the bevel band flush to the upper and lower faces; the bevel and straight heads are independent.

09

Head-and-tail trimming, bevel and straight

Both formats share one end-trimming head, so the changeover does not wait for a second cut.

10

Straight fine trimming

The straight edge has its own finishing head, so the bevel setting is left untouched when the format changes.

11

Straight and bevel scraping

One scraping head serves both formats, so a changeover does not need a second setting.

12

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

13

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

14

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM368JCD
Feed rate	16 – 23 m/min
Panel width	≥ 60 mm straight / ≥ 80 mm bevel
Panel thickness	9 – 60 mm straight / 15 – 40 mm bevel
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	13
Control screen	Numeric panel or industrial touch screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	22 kW
Machine size (L × W × H)	7800 × 800 × 1750 mm

Values from the FM368JCD technical data sheet and the 2026 configuration list.

What the machine is built to do

45° cut and milled in one set-upThe square edge is cut to 45° and the flat face milled into the bevel in the same pass — no second machine, no re-fixturing.
Pre-milling before gluingTwo cutters take the saw marks and the out-of-square edge off the panel first, so the band meets a clean face instead of bridging a ripple.
Bevel and straight on one bedThe same line finishes the 45° mitre and the square edge; the station list changes, the operating logic does not.
Precise flat scrapingA flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
Two polishing headsA second set of cotton wheels finishes the edge after the first pass, for a higher sheen on the joint.