Name: FM368JCS 45° Bevel Edge Bander with Heat Lamp
Brand: CNSK
SKU: FM368JCS

Overview

Twelve processing cells: 45° saw cutting, pre-milling, band grooving, bevel gluing, heat lamp, synchronous bevel pressing, bevel fine trimming, end trimming, fine trimming, bevel scraping, cleaning and polishing.
The heat lamp raises the board temperature before the press, which keeps the bond even in a cold shop.
15–55 mm panels, ≥ 100 mm width, 14 m/min.
7,500 mm bed; 26.72 kW total, 380 V, 0.7 MPa air.
Frame at 1,680 mm — the lowest build in the 3 series for container loading.

FM368JCS CNSK · Dongguan

Feed rate14 m/min

Panel thickness15 – 55 mm

Panel width≥ 100 mm

Processing stations12

Total power26.72 kW

Station sequence

Set the job on the screen; the heat lamp sits between the bevel gluing unit and the pressing group.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

45° saw cutting

One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

05

Bevel gluing

A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.

06

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

07

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

08

Bevel fine trimming

Special trim knives bring the bevel band flush to the upper and lower faces; the bevel and straight heads are independent.

09

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

10

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

11

Bevel scraping

Scraping on the bevel faces removes knife marks and surplus glue on both faces of the 45° band.

12

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

13

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM368JCS
Feed rate	14 m/min
Panel width	≥ 100 mm
Panel thickness	15 – 55 mm
Edge band thickness	0.4 – 1.5 mm
Edge band width	22 – 70 mm
Pressure beam	Electric lift
Processing stations	12
Control screen	Numeric panel or industrial touch screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	26.72 kW
Machine size (L × W × H)	7500 × 940 × 1680 mm

Values from the FM368JCS technical data sheet and the 2026 configuration list.

What the machine is built to do

45° cut and milled in one set-upThe square edge is cut to 45° and the flat face milled into the bevel in the same pass — no second machine, no re-fixturing.
Pre-milling before gluingTwo cutters take the saw marks and the out-of-square edge off the panel first, so the band meets a clean face instead of bridging a ripple.
Band groovingGrooves cut on the inner face of the band let it bend and press cleanly around a 45° corner.
Electric beam liftThe pressure beam is set from the screen rather than by hand crank, so a mixed batch of thicknesses needs no reset between panels.