Name: FM386JAH Track-Fed Two-Pot Edge Bander with Notching
Brand: CNSK
SKU: FM386JAH

Overview

Twelve processing cells: track conveyor, pre-milling, two glue pots with fast-melt tanks, two pressing groups, head-and-tail trimming, rough and fine trimming, scraping, double polishing and notching.
The crawler conveyor carries the panel through the eight-metre bed at constant speed.
The 21.5-inch industrial screen carries the recipes for both pots and for the notching unit.
9–60 mm panels, ≥ 50 mm width, 16–23 m/min.
20 kW total, 380 V, 0.7 MPa air; frame at 750 mm width.

FM386JAH CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 mm

Panel width≥ 50 mm

Processing stations12

Total power20 kW

Station sequence

Two identical glue groups, each with its own fast-melt tank and pressing group; the notching unit closes the line.

01

Track conveyor

A crawler conveyor supports the panel and drives it through every cell at constant speed.

02

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Gluing furnace with fast-melt tank

EVA pot with a fast-melt tank, so the adhesive reaches working temperature quickly and holds it through the shift.

05

Pressing, first group

The first pressure group seats the band applied at the first glue station.

06

Gluing furnace with fast-melt tank

EVA pot with a fast-melt tank, so the adhesive reaches working temperature quickly and holds it through the shift.

07

Pressing, second group

A second pressure group follows the second glue station, for the band applied there.

08

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

09

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

10

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

11

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

12

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

13

Notching

A slotting unit cuts the notches the profile needs after banding, so a notched panel does not need a second machine.

Technical data

Model	FM386JAH
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	12
Control screen	21.5-inch industrial touch screen
Input voltage	380 V
Air pressure	0.7 MPa
Total power	20 kW
Machine size (L × W × H)	8800 × 750 × 1750 mm

Values from the FM386JAH technical data sheet and the 2026 configuration list.

What the machine is built to do

Track conveyor infeedA crawler conveyor supports the panel and drives it at constant speed through every cell, which keeps long panels from drifting.
Pre-milling before gluingTwo cutters take the saw marks and the out-of-square edge off the panel first, so the band meets a clean face instead of bridging a ripple.
Fast-melt tankThe melt reaches working temperature in less time, so the first panel of a shift is not scrap.
21.5-inch industrial screenA large touch screen carries the recipe list and the station settings, with parameter changes shown live.
Notching on the lineThe slotting unit cuts the notches a profile panel needs after banding, so the part does not come off the line for a second operation.