Name: FM465 Straight Edge Bander
Brand: CNSK
SKU: FM465

Overview

Nine processing stations on one frame: heat lamp, gluing, pressing, head and tail trimming, fine trimming, corner tracking, scraping, cleaning and double polishing.
5,300 mm is the shortest bed in the 4 series that still carries a full finishing train, which matters where floor space decides what a shop can buy.
No pre-milling station. The FM465 is specified for panels that arrive square from a well-set saw, and the saving goes into the finishing end instead of the front end.
9 to 60 mm at the beam, so a 9 mm skin and a 60 mm worktop run on the same setting.
The pressure beam lifts electrically and the height is entered on the screen, not cranked by hand.
The corner tracking motor follows the end of the panel, so the band stops where the panel stops instead of leaving a step.
Frame height 1,750 mm as standard, 1,350 mm for container loading.

FM465 CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 mm

Pressure beamElectric lift

Stations9

Bed5,300 mm

Station sequence

The job is set on the control screen; the panel then meets nine processing cells in this order.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

03

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

04

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

05

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

06

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

07

Corner rounding, head tracking

A high-frequency trimming motor profiles the corners at both ends, so the banded edge runs round the panel without a step.

08

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

09

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

10

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Model	FM465
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift, to 65 mm
Processing stations	9
Control screen	Control screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	14 kW
Machine size (L × W × H)	5300 × 670 × 1750 mm

Values from the FM465 technical data sheet and the 2026 configuration list.

Nine stations, one frameHeat, glue, press, head and tail trim, fine trim, corner tracking, scrape, clean and polish sit in that order on one 5,300 mm bed, so the panel never leaves the machine between them.
No pre-milling, by designA panel that arrives square from the saw does not need a milling head; leaving it out shortens the frame and lowers the price without changing how the joint looks.
Straight edge 9 to 60 mmA 9 mm skin and a 60 mm worktop pass under the same pressure beam, set once from the screen.
Corner trackingA high-frequency motor follows the trailing end and rounds the corner, which is the difference between a finished edge and a trimmed one.
Electric beam liftHeight is set electrically up to 65 mm, which is what makes short runs of very different thicknesses practical rather than slow.
1,350 mm shipping heightBuilt at 1,750 mm as standard; the low-frame version goes into a 40 ft container instead of a flat rack.