FM468CX
45° Full-Bevel and Bevel-Straight Edge Bander
A 45° full bevel line and a straight edge line on the same frame, changed over from the screen, so one machine covers both the seamless corner and the ordinary panel.
Overview
- Fifteen cells on one bed: servo milling, 45° gluing, grooving, a second heat lamp, bevel and straight pressing, bevel trimming, end trimming, corner tracking, bevel scraping, cleaning and polishing.
- Two formats from one frame: 45° full bevel for the seamless corner, straight edge for ordinary work. The format is selected at the screen, not rebuilt on the bed.
- PUR gluing serves the bevel and the straight edge from a no-cleaning pot, so a change of band colour does not cost a solvent soak.
- Servo milling and servo 45° gluing: the cut and the glue film are set from the screen and repeat without a test panel.
- Edge band grooving is servo driven as well, which is what keeps the groove aligned with the 45° face through a batch.
- 12 to 25 mm at the beam, panels from 120 mm wide, 5 or 8 m/min feed.
- 27 kW total; frame 6,290 × 950 × 1,700 mm, 21.5-inch industrial screen.
FM468CX
CNSK · Dongguan
Feed rate5 / 8 m/min
Panel thickness12 – 25 mm
Panel width≥ 120 mm
Stations14
Total power27 kW
Station sequence
Set the format on the 21.5-inch screen; the panel then passes fourteen processing cells, bevel or straight.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Servo milling
Servo-controlled diamond cutters mill both formats to micron precision, and switch between them from the screen.
03
Servo 45° full-bevel gluing
A servo module applies glue and seats the band on inclined faces of different thickness, for a seamless bevel.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
PUR gluing, bevel and straight
A no-cleaning PUR pot serves both the bevel and the straight edge; the pot is switched with the format and cleaned without a solvent soak.
06
Servo band grooving
Servo-positioned grooving on the inner face of the band, for a 45° bend with a crisp surface contour.
07
Heat lamp after grooving
A second lamp reheats the band and the panel after grooving, so the 45° band is still soft when it reaches the press.
08
Bevel and straight pressing
Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.
09
45° lower face fine trimming
The excess band is cut off the underside of the full-bevel panel, leaving the bottom face flat and smooth.
10
45° panel face fine trimming
The overhang on the upper and lower faces of the bevel or bevel-straight panel is cut back flush.
11
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
12
Corner rounding, head tracking
A high-frequency trimming motor profiles the corners at both ends, so the banded edge runs round the panel without a step.
13
Bevel scraping
Scraping on the bevel faces removes knife marks and surplus glue on both faces of the 45° band.
14
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
15
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM468CX |
| Feed rate | 45° bevel straight 5 m/min · full bevel 8 m/min |
| Panel width | ≥ 120 mm |
| Panel thickness | 12 – 25 mm |
| Edge band thickness | 0.8 – 1.0 mm |
| Edge band width | 30 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 14 |
| Control screen | 21.5-inch industrial computer, Windows |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 27 kW |
| Machine size (L × W × H) | 6290 × 950 × 1700 mm |
| Machine weight | 2,400 kg |
Values from the parameter table in the FM468CX English technical data: bevel-straight feed 5 m/min, full bevel 8 m/min, edge band 0.8 – 1.0 mm thick and 30 – 65 mm wide, 2,400 kg machine weight.
What the machine is built to do
- Two formats, one bed45° full bevel and straight edge are both built into the same frame; the job is chosen on the screen and the pressing section follows it.
- Servo milling and servo 45° gluingThe milling cut and the glue film are positioned by servo motor, so a repeat batch starts from the same numbers as the first one.
- PUR on both edgesA no-cleaning PUR pot feeds the bevel and the straight edge, which keeps colour changes cheap on short runs.
- Servo band groovingThe groove that receives the 45° band is cut under servo control, aligned with the bevel face rather than set by hand.
- 21.5-inch industrial screenParameters, station status and servo positions are read and set on a Windows industrial computer, not on a small numeric panel.
- Bevel and straight pressingOne pressing section handles straight, bevel and the mixed format, so the changeover is a screen step rather than a mechanical one.
Edge samples
More from the 4 series
FM490G
Servo Narrow-Panel Edge Bander
Forty-millimetre strips, 9–60 mm thick, at 16–23 m/min — with servo control on the stations that decide the finish.
16 processing cells≥ 40 mm width9 – 60 mm thick16 – 23 m/min
Read the specification
FM468JCD
45° Bevel and Straight Edge Bander
45° bevel and straight edge banding, switched with one key, on a 9,900 mm bed.
15 processing cells8–60 / 12–40 mm45° bevelFast-melt
Read the specification
FM465
Straight Edge Bander
Nine stations on a 5,300 mm bed, 9 to 60 mm panels and no pre-milling: a straight bander for shops whose saw already cuts clean.
9 stations9–60 mm16–23 m/min5.3 m bed
Read the specification
Put FM468CX against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.