Name: FM468J Straight Edge Bander
Brand: CNSK
SKU: FM468J

Overview

Twelve processing stations: pre-milling, heat lamp, gluing, pressing, head and tail trimming, rough trimming, fine trimming, corner tracking, scraping, precise flat scraping, cleaning and double polishing.
7,000 mm bed, the longest straight frame in the 4 series, which is what carries pre-milling plus two trimming heads plus flat scraping.
Pre-milling squares the edge before gluing; rough and fine trimming then split the overhang between two heads.
Precise flat scraping removes the glue film before the polishing wheels touch the edge.
9 to 60 mm at the beam, 16 to 23 m/min, 17.56 kW total.
Electric beam lift to 65 mm, height entered from the screen.
Frame 1,750 mm as standard, 1,350 mm for container loading.

FM468J CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 mm

Stations12

Bed7,000 mm

Total power17.56 kW

Station sequence

Screen first; pre-milling opens the sequence, double polishing ends it.

01

Control screen

Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.

02

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

03

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

04

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

05

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

06

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

07

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

08

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

09

Corner rounding, head tracking

A high-frequency trimming motor profiles the corners at both ends, so the banded edge runs round the panel without a step.

10

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

11

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

12

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

13

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Technical data

Model	FM468J
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift, to 65 mm
Processing stations	12
Control screen	Control screen, per configuration
Input voltage	380 V
Air pressure	0.7 MPa
Total power	17.56 kW
Machine size (L × W × H)	7000 × 740 × 1750 mm

Values from the FM468J technical data sheet and the 2026 configuration list.

What the machine is built to do

Twelve stations, 7,000 mmPre-milling, heat, glue, press, head and tail trim, rough, fine, corner tracking, scrape, flat scrape, clean and polish, all on one bed.
Pre-milling before the glue potA fresh, square edge takes a straight band; a saw mark does not.
Rough and fine on separate headsThe overhang is taken in two cuts, so the finishing knife only removes the last fraction.
Flat scraping before polishingGlue film along the joint is scraped off, which is what keeps a polished edge from going dull in service.
17.56 kW installedThree-phase 380 V supply, with the beam, the drives and the polishing motors on the same cabinet.
1,350 mm shipping heightThe low-frame version loads into a 40 ft container; 1,750 mm is standard.