FM469JCD
45° Bevel and Straight Edge Bander
Fifteen stations on 10,700 mm, 45° bevel and straight edge in the same pass, with four tracking heads holding both faces so neither end is left proud.
Overview
- Fifteen processing stations, from separating agent and pre-milling through the 45° saw, groove cutting, bevel gluing, pressing, rough trimming, integrated end trimming, straight and bevel trimming, four-head tracking, scraping, cleaning and double polishing.
- 45° bevel and straight edge on one bed: the bevel gives the seamless corner, the straight edge covers ordinary panels, and the format is chosen at the screen.
- Four tracking heads work the bevel and the straight face together, so the band is cut round both ends in one pass.
- Separating agent is applied before gluing, so the band releases cleanly where the bevel face meets it.
- Straight 9 to 60 mm, bevel 15 to 40 mm; panel width from 60 mm straight, 80 mm bevel.
- 24 kW total; frame 10,700 × 740 × 1,750 mm.
- Frame 1,750 mm as standard, 1,350 mm for container loading.
FM469JCD
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel thickness9 – 60 mm straight · 15 – 40 mm bevel
Panel width≥ 60 mm straight · ≥ 80 mm bevel
Stations15
Total power24 kW
Station sequence
Screen first, then the panel meets fifteen processing cells in this order; bevel and straight share the same sequence.
01
Control screen
Job set-up runs from the screen — parameters entered by touch or input box — and a change shows its effect at once.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
45° saw cutting
One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.
05
Band grooving
Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.
06
Bevel gluing
A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.
07
Gluing furnace
EVA glue pot; the melt is held at working temperature through the shift.
08
Fast-melt glue
The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.
09
Bevel and straight pressing
Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.
10
Rough trimming
The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.
11
Head-and-tail trimming, bevel and straight
Both formats share one end-trimming head, so the changeover does not wait for a second cut.
12
Straight and bevel fine trimming
One trimming head takes the overhang off the straight face and the bevel face, bringing both flush with the panel.
13
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
14
Straight and bevel scraping
One scraping head serves both formats, so a changeover does not need a second setting.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM469JCD |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 60 mm straight / ≥ 80 mm bevel |
| Panel thickness | 9 – 60 mm straight / 15 – 40 mm bevel |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift, to 65 mm |
| Processing stations | 15 |
| Control screen | Control screen, per configuration |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 24 kW |
| Machine size (L × W × H) | 10700 × 740 × 1750 mm |
Values from the FM469JCD technical data sheet. The sheet header prints FM569JACD, a typographical error in the source document; the figures below are the ones listed for this machine.
What the machine is built to do
- Fifteen stations on 10,700 mmSeparating agent, pre-milling, 45° saw, groove, gluing, pressing, four trimming and tracking cells, scraping, cleaning and double polishing.
- Bevel and straight in one passThe 45° saw and the bevel glue pot run in the same sequence as the straight edge station, so a mixed order does not need a second machine.
- Four-head trackingTwo heads per face follow the panel end and cut the band round the corner, bevel and straight together.
- Separating agentApplied before gluing so the band releases where it should on a bevel joint, instead of tearing on the face.
- Glue pot and fast-melt unitA conventional pot and a fast-melting unit on the same frame, so the glue can be changed without stopping the line for a full melt.
- Two thickness ranges9 to 60 mm straight, 15 to 40 mm bevel, with the two formats sharing the pressure beam.
Edge samples
More from the 4 series
FM490G
Servo Narrow-Panel Edge Bander
Forty-millimetre strips, 9–60 mm thick, at 16–23 m/min — with servo control on the stations that decide the finish.
16 processing cells≥ 40 mm width9 – 60 mm thick16 – 23 m/min
Read the specification
FM468JCD
45° Bevel and Straight Edge Bander
45° bevel and straight edge banding, switched with one key, on a 9,900 mm bed.
15 processing cells8–60 / 12–40 mm45° bevelFast-melt
Read the specification
FM465
Straight Edge Bander
Nine stations on a 5,300 mm bed, 9 to 60 mm panels and no pre-milling: a straight bander for shops whose saw already cuts clean.
9 stations9–60 mm16–23 m/min5.3 m bed
Read the specification
Put FM469JCD against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.