Name: FM480JSF Straight Edge Bander
Brand: CNSK
SKU: FM480JSF

Overview

Eleven processing stations: pre-milling, heat lamp, gluing, pressing, head and tail trimming, rough trimming, servo fine trimming, two-speed head tracking, scraping, cleaning and double polishing.
The 21.5-inch industrial computer runs the job: parameters, station status and the servo positions of the trimming heads.
Fine trimming is positioned by servo motor, so the depth is a number entered on the screen rather than a dial crept up on.
Two high-speed motors cut the band at the ends and two servo motors hold the chamfer tracking, so the corner follows the panel.
7,350 mm bed, 9 to 60 mm panels, 16 to 23 m/min feed, 14 kW total.
Electric beam lift to 65 mm, height set from the screen.
Frame 1,750 mm as standard, 1,350 mm for container loading.

FM480JSF CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 mm

Stations11

Bed7,350 mm

Screen21.5-inch industrial

Station sequence

The job is set on the 21.5-inch screen; the panel then meets eleven processing cells in this order.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

03

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

04

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

05

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

06

Head-and-tail trimming

The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.

07

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

08

Servo fine trimming

The fine-trimming cutter is positioned by servo motor instead of by hand, so the depth comes from the screen and a changeover needs no test board.

09

Head tracking, two high-speed and two servo motors

Two high-speed motors cut the band at the leading and trailing ends, and two servo motors hold the chamfer tracking, so the corner radius follows the panel.

10

Scraping

Upper and lower edges are scraped to remove trim knife marks, and surplus glue between band and panel comes off.

11

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

12

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Technical data

Model	FM480JSF
Feed rate	16 – 23 m/min
Panel width	≥ 50 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift, to 65 mm
Processing stations	11
Control screen	21.5-inch industrial computer, Windows
Input voltage	380 V
Air pressure	0.7 MPa
Total power	14 kW
Machine size (L × W × H)	7350 × 740 × 1750 mm

Values from the FM480JSF technical data sheet and the 2026 configuration list.

What the machine is built to do

Servo fine trimmingThe fine trimming head is positioned by servo motor; a change of band thickness is a value on the screen, and the first panel is already on size.
Two high-speed ends, two servo tracking motorsThe ends are cut by high-speed motors while two servo motors hold the chamfer tracking, so the corner radius follows the panel.
21.5-inch industrial screenWindows industrial computer, with parameter entry, station status and servo diagnostics in one place.
Pre-milling plus rough and fineThe edge is squared before gluing, the overhang is split between two heads, and the finish is taken by the servo head.
7,350 mm bedLength enough for eleven stations without crowding the outfeed, and a stable base for the servo heads.
1,350 mm shipping heightStandard build 1,750 mm; the low frame goes into a 40 ft container.