Name: FM586JASK High-Speed Straight Edge Bander
Brand: CNSK
SKU: FM586JASK

Overview

Eighteen numbered cells: separating agent, pre-milling, baking lamp 1, straight edge gluing, pressing group 1, baking lamp 2, EVA pot, fast-melt tank, pressing group 2, double-track head-and-tail trimming, rough and fine trimming, four-head tracking, double scraping, flat scraping, cleaning, polishing 1 and polishing 2.
16 to 26 m/min feed. The upper end is reached with a new-generation control system and stable automatic panel feed, not by shortening the finishing train.
Two baking lamps, one either side of the glue pot, so the panel edge is warm at the first glue station and still warm at the second.
Two pressing groups, each following its own glue station, so a second band applied after the pot is pressed as firmly as the first.
Double-track head-and-tail trimming, double scraping and two polishing units: the finishing end is duplicated to keep up with the feed speed.
9 to 60 mm panels from 60 mm wide, 0.4 to 3 mm band, 12 to 65 mm band width, 22.5 kW.
10,800 mm bed with a 21.5-inch industrial screen, and a 1,750 mm frame as standard.

FM586JASK CNSK · Dongguan

Feed rate16 – 26 m/min

Panel thickness9 – 60 mm

Stations18

Total power22.5 kW

Bed10,800 mm

Station sequence

Station 01 is the screen; the eighteen cells then run from separating agent to the second polishing unit.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

Baking lamp

A lamp heats the band and the panel edge before the glue station, so the melt meets a warm face instead of a cold one.

05

Gluing

Hot-melt adhesive is melted and applied to the panel edge before the band is pressed on.

06

Pressing, first group

The first pressure group seats the band applied at the first glue station.

07

Baking lamp

A lamp heats the band and the panel edge before the glue station, so the melt meets a warm face instead of a cold one.

08

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

09

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

10

Pressing, second group

A second pressure group follows the second glue station, for the band applied there.

11

Head-and-tail trimming, double track

Two tracks run the ends, so a pair of panels is trimmed without dropping the feed speed.

12

Rough and fine trimming

Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.

13

Four-head corner tracking

Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.

14

Double-edge scraping

Scraping on both edges of the run, for trim marks and surplus glue on either face.

15

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

16

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

17

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

18

Second polishing

A second pair of cotton wheels follows the first, for a higher sheen on the joint than one pass gives.

Technical data

Model	FM586JASK
Feed rate	16 – 26 m/min
Panel width	≥ 60 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	18
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	22.5 kW
Machine size (L × W × H)	10800 × 800 × 1750 mm

Values from the FM586JASK technical data sheet and the 2026 configuration list.

What the machine is built to do

26 m/min without a shorter trainThe feed speed is quoted with the full eighteen-cell sequence behind it, which is the only version of the number that matters on a shop floor.
Two lamps, two pressing groupsA lamp before each glue station and a pressing group after it: the first band and the second band are heated and pressed with the same authority.
Double-track end trimmingTwo tracks run the ends in parallel, so a pair of panels is trimmed without dropping the feed.
Duplicated finishing endDouble scraping, precise flat scraping, cleaning and two polishing units keep the surface finish at the same standard when the line runs at 26 m/min.
Four-head trackingTwo heads at each end cut the band round the corner radius, so a fast line still produces a corner that reads finished.
21.5-inch screenThe job is set on a 21.5-inch industrial computer: thickness, band and station parameters from one screen, with the option of a mouse and keyboard.