Name: FM586JF PUR Edge Bander for Honeycomb Panels
Brand: CNSK
SKU: FM586JF

Overview

Fourteen numbered cells behind the crawler conveyor: separating agent, pre-milling, two-colour PUR no-cleaning pot, pressing, belt pressing, double-track head-and-tail trimming, rough and fine trimming, four-head tracking, double scraping, precise flat scraping, cleaning, polishing 1 and polishing 2.
Built for aluminium honeycomb panels: the pressing section is extra-long and a belt carries the load, so the thin aluminium skin is held flat while the adhesive cures.
Wood and aluminium on the same machine — the edge banding of honeycomb panels and of wooden panels is switched with one key, so a mixed order does not need two lines.
Heavy-duty frame, finish-milled on a large gantry machine, then crawler pressing: the bed stays straight under a stack of honeycomb doors.
Two-colour PUR no-cleaning pot: two adhesive colours, even dispensing, and cleaning without a solvent soak.
14 to 23 m/min, 18 kW, 10,300 mm bed; band from 0.4 to 1.5 mm thick and 12 to 65 mm wide, panels from 60 mm wide and 9 to 60 mm thick.
Four-head tracking and double scraping on the same frame, so the corner and the glue film are handled after the PUR joint.

FM586JF CNSK · Dongguan

Feed rate14 – 23 m/min

Panel thickness9 – 60 mm

Stations14

Total power18 kW

Bed10,300 mm

Station sequence

Station 01 is the screen; fourteen cells follow, with the PUR pot in fourth position and the belt press behind the first pressing group.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

PUR gluing

A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.

05

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

06

Belt pressing

A pressure belt holds the band against the edge over a longer contact length than wheels alone, which is what a honeycomb skin needs while the adhesive sets.

07

Head-and-tail trimming, double track

Two tracks run the ends, so a pair of panels is trimmed without dropping the feed speed.

08

Rough and fine trimming

Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.

09

Four-head corner tracking

Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.

10

Double-edge scraping

Scraping on both edges of the run, for trim marks and surplus glue on either face.

11

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

12

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

13

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

14

Second polishing

A second pair of cotton wheels follows the first, for a higher sheen on the joint than one pass gives.

Technical data

Model	FM586JF
Feed rate	14 – 23 m/min
Panel width	≥ 60 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 1.5 mm
Edge band width	12 – 65 mm
Pressure beam	Crawler pressing, electric lift
Processing stations	14
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	18 kW
Machine size (L × W × H)	10300 × 900 × 1800 mm

Values from the FM586JF technical data sheet and the 2026 configuration list. The band thickness range is narrower than on an EVA machine because the PUR pot is specified for thin aluminium and wood bands.

What the machine is built to do

One key, aluminium or woodThe machine is specified for aluminium honeycomb as well as wooden panels, and the changeover between them is a setting rather than a rebuild.
Belt pressing plus wheel pressingA pressure belt holds the band over a longer contact length, which is what a honeycomb panel needs; the wheel group behind it finishes the joint.
Extra-long pressing sectionThe distance between gluing and the end of pressing is longer than on a standard line, giving PUR the time to set before the panel is trimmed.
Gantry-milled heavy frameThe frame is machined on a large gantry mill before assembly, so the crawler stays true under load and the band does not drift on long panels.
Two-colour PUR potTwo adhesive colours from one no-cleaning pot, dispensed evenly, with cleaning that does not need a solvent soak.
Four-head trackingThe corner is cut round the radius at both ends, so a honeycomb door closes on a finished corner rather than a trimmed one.