FM668GJAZ
Narrow-Board Edge Bander with PUR
Forty-millimetre strips are where a bander shows whether it was built for them: the FM668GJAZ carries a 1,050 mm wide bed and a heavy pressure beam, so a narrow board stays under the beam instead of tipping out of it.
Overview
- Sixteen numbered cells behind a heavy pressure beam: separating agent, pre-milling, heat lamp 1, EVA furnace, pressing group 1, two-colour PUR pot, heat lamp 2, pressing group 2, head-and-tail trimming, rough and fine trimming, head tracking, double-edge scraping, precise flat scraping, cleaning and double polishing.
- Two heat lamps and two pressing groups, one pair either side of the two glue systems, so a band applied at the PUR pot is heated and pressed with the same authority as the one from the EVA furnace.
- 1,050 mm wide bed on a 10,080 mm frame. The extra width is frame, not decoration: it is what keeps a 40 mm strip flat when the pressure beam comes down.
- EVA furnace and a two-colour PUR no-cleaning pot on one frame, so the adhesive is picked to the order rather than to the machine.
- 16 to 23 m/min, 22 kW, panels from 40 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
- Double-edge scraping and precise flat scraping finish both the straight edge and the film, and two polishing units follow them.
- 21.5-inch industrial computer as station 01, with the job set from the screen instead of from a row of dials.
FM668GJAZ
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations16
Total power22 kW
Bed10,080 mm
Station sequence
Station 01 is the 21.5-inch screen; sixteen numbered cells run from separating agent to double polishing.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
Gluing furnace
EVA glue pot; the melt is held at working temperature through the shift.
06
Pressing, first group
The first pressure group seats the band applied at the first glue station.
07
PUR gluing
A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.
08
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
09
Pressing, second group
A second pressure group follows the second glue station, for the band applied there.
10
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
11
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
12
Head tracking
Two heads follow the leading and trailing end of the panel, so the band is cut round the corner instead of square across it.
13
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
14
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM668GJAZ |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Heavy-duty beam, electric lift |
| Processing stations | 16 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 22 kW |
| Machine size (L × W × H) | 10080 × 1050 × 1800 mm |
Values from the FM668GJAZ technical data sheet and the 2026 configuration list. The sheet header reads M668GJAZ; the model is FM668GJAZ.
What the machine is built to do
- Built around the 40 mm stripThe bed is 1,050 mm wide and the beam is a heavy casting: a narrow board is held across its full width, which is the difference between a flat band and one that rides up at the trimming head.
- Two lamps, two presses, two gluesHeat lamp, EVA furnace, press, PUR pot, heat lamp, press: each adhesive gets its own lamp and its own pressing group, so neither is run at the setting of the other.
- PUR without a second machineThe two-colour no-cleaning pot covers the joints that have to hold in a wet or hot room; the EVA furnace still does the everyday work.
- Head tracking at both endsThe tracking heads follow the leading and trailing end of the strip, so the band turns the corner instead of being cut square across it.
- Double scraping, then flat scrapingTwo scraping heads take the band and the glue film, and the precise flat scraper cleans the panel face behind them.
- 21.5-inch screenThickness, band and station settings are entered on a 21.5-inch industrial computer; the recipe is recalled rather than reset.
Edge samples
More from the 6 series
FM668JAZ
Compact Narrow-Board Edge Bander with PUR
Sixteen-station narrow-board line on a 9.3 m bed: two lamps, two pressing groups and a two-colour PUR pot, in a shorter bay.
16 stations40 mm narrow boards9.3 m bedEVA and PUR
Read the specification
FM668GJZ
Narrow-Board Edge Bander with Grooving
Fourteen stations on a 10.1 m heavy-frame bed: band grooving, one heat lamp and press group, 18.55 kW, strips from 40 mm.
14 stationsBand groovingHeavy pressure beam10.1 m bed
Read the specification
FM669GD
Narrow-Board Edge Bander with Diamond Trimming
Diamond fine trimming, diamond profile tracking and servo scraping on sixteen stations, for narrow boards from 40 mm wide.
16 stationsDiamond trimmingServo scraping19.5 kW
Read the specification
Put FM668GJAZ against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.