Name: FMK830 Intelligent laser crawler edge banding machine
Brand: CNSK
SKU: FMK830

Overview

Eighteen cells in the order printed on the sheet: 21.5-inch industrial computer, crawler conveyor, heavy-duty one-piece bed rail, separating agent, pre-milling, heat lamp, two-colour PUR pot, pressing, laser operating system, swing-type cutter and tape feed, swing-type pressing, double-track head-and-tail alignment, fine trimming, double scraping, head tracking, cleaning, polishing and notching.
Laser bonding replaces the glue: the laser unit activates the functional layer on the band, so the finished joint has no visible glue line and needs no EVA melt in the line.
A two-colour PUR no-cleaning pot is still fitted at station 07, so the same machine can run PUR band as well as laser band.
Heavy-duty one-piece bed rail and a heavy steel pressure beam carry the panel; the crawler conveyor keeps the feed constant through eighteen cells.
Panels from 60 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
16 to 23 m/min on a 10,300 mm frame, 950 mm wide and 1,750 mm high, with 28 kW installed.
Notching sits last at station 18, so a slotted part comes off the line finished instead of going to a second machine.

FMK830 CNSK · Dongguan

Feed rate16 – 23 m/min

Panel width≥ 60 mm

Stations18

Total power28 kW

Frame10,300 mm

Station sequence

Station 01 is the 21.5-inch computer, station 02 the crawler conveyor and station 09 the laser operating system; the eighteen cells follow the order printed on the sheet.

01

21.5-inch control screen

Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.

02

Track conveyor

A crawler conveyor supports the panel and drives it through every cell at constant speed.

03

Heavy-duty one-piece bed rail

A one-piece guide-rail beam carries a heavy steel pressure beam; the section is sized for the load a 45° cut puts through the bed.

04

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

05

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

06

Heat lamp

The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.

07

Two-colour PUR no-cleaning pot

The pot holds two PUR colours and switches between them without a solvent flush, and it sits outside the machine so the melt is kept apart from the EVA furnace.

08

Pressing

High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.

09

Laser operating system

The laser source, its power curve and the band feed are run from one controller, so a change of band is a recipe change rather than a re-setup.

10

Swing-type cutter and tape feed

The cutter swings to the band angle and the tape feed follows it, so a change of band width is a setting rather than a tool change.

11

Swing-type pressing

The pressure roller swings on an arc and cushions the load at the joint instead of hitting the band flat.

12

Double-track head-and-tail alignment

Two guide tracks move the end-trimming heads, so both ends are aligned and cut without dropping the feed speed.

13

Fine trimming

The finishing cut takes the overhang back to the panel face; this is the pass that decides how clean the joint reads.

14

Double-edge scraping

Scraping on both edges of the run, for trim marks and surplus glue on either face.

15

Head tracking

Two heads follow the leading and trailing end of the panel, so the band is cut round the corner instead of square across it.

16

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

17

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

18

Notching

A slotting unit cuts the notches the profile needs after banding, so a notched panel does not need a second machine.

Technical data

Model	FMK830
Feed rate	16 – 23 m/min
Panel width	≥ 60 mm
Panel thickness	9 – 60 mm
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Heavy-duty electrical lift on a one-piece bed rail
Processing stations	18
Control screen	21.5-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	28 kW
Machine size (L × W × H)	10300 × 950 × 1750 mm

Values from the FMK830 technical data sheet in the 2026 configuration list, built to the Korean market configuration.

What the machine is built to do

Laser unit on the frameThe laser sits between the pressing groups and activates the band's functional layer, which is what removes the glue line from the joint.
Two-colour PUR as wellThe pot switches between two PUR colours without a solvent flush, so laser and PUR work can be quoted from the same machine.
Swing cutter and swing pressThe cutter swings to the band angle and the pressure roller follows it on an arc, which cushions the load at the joint.
Double-track end trimmingTwo tracks move the end heads, so both ends are aligned and cut without dropping the feed speed.
Heavy bed railA one-piece guide rail and a heavy pressure beam hold the panel flat under the laser head.
Notching on the same lineThe slotting unit at station 18 cuts the notches a profile part needs after banding.