Laser800
Intelligent laser edge banding machine
Laser activation at station 06 with a cooling unit behind it: the joint is made without a glue line, and the machine still carries a two-colour PUR pot for band that needs adhesive.
Overview
- Fourteen cells in the order printed on the sheet: 21.5-inch industrial computer, separating agent, pre-milling, two-colour PUR pot, pressing group 1, laser operating system, laser cooling system, pressing group 2, head-and-tail trimming, rough and fine trimming, four-head tracking, double scraping, precise flat scraping and double polishing.
- Laser bonding replaces the glue line: the laser activates the functional layer on the band, and a cooling unit keeps the head at working temperature through the shift.
- A two-colour PUR no-cleaning pot at station 04 covers band that has to be glued rather than laser-bonded.
- Panels from 40 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
- 16 to 23 m/min on a 10,080 mm frame, 1,000 mm wide and 1,750 mm high, with 22.5 kW installed.
- Pressing runs on both sides of the laser unit, so the band is seated before activation and pressed again behind it.
- Double scraping and precise flat scraping follow the trimmers, then two polishing heads finish the edge.
Laser800
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations14
Total power22.5 kW
Frame10,080 mm
Station sequence
Station 01 is the 21.5-inch computer and station 06 the laser operating system; the fourteen cells follow the order printed on the sheet.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Two-colour PUR no-cleaning pot
The pot holds two PUR colours and switches between them without a solvent flush, and it sits outside the machine so the melt is kept apart from the EVA furnace.
05
Pressing, first group
The first pressure group seats the band applied at the first glue station.
06
Laser operating system
The laser source, its power curve and the band feed are run from one controller, so a change of band is a recipe change rather than a re-setup.
07
Laser cooling system
A closed cooling circuit holds the laser at working temperature, so the bond stays even across a long shift.
08
Pressing
High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.
09
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
10
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
11
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
12
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
13
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
14
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | Laser800 |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 14 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 22.5 kW |
| Machine size (L × W × H) | 10080 × 1000 × 1750 mm |
Values from the Laser800 technical data sheet in the 2026 configuration list.
What the machine is built to do
- Laser unit with coolingThe laser sits at station 06 with a dedicated cooling system behind it, which is what lets the head run continuously rather than in cycles.
- PUR as a second pathThe two-colour pot still runs, so a shop can quote laser work and PUR work from the same frame.
- Two pressing groupsOne ahead of the laser and one behind it: the band is seated, activated, then pressed again while it is warm.
- Four-head trackingFour motors carry the tracking unit, so both corners are turned in the same pass.
- Double polishingTwo sets of cotton wheels finish the joint, which is where a glue-free band shows its advantage.
- Ten metre frame10,080 mm long and 1,000 mm wide, with fourteen cells: a laser line without an EVA furnace in it.
More from the 8 series
FM820JCDH
Skeleton-Line Grille Edge Bander
Skeleton-line doors, grille slats and standard straight edge banding on one track-fed 13-metre bed.
18 processing cells9–60 / 15–40 mmSkeleton lineTrack feed
Read the specification
Laser830
Intelligent laser edge banding machine
Sixteen cells: EVA furnace and two-colour PUR pot ahead of the laser unit, then double scraping and two polishing heads, at 22.5 kW.
16 stationsEVA furnace and PURLaser unit8.5 m width
Read the specification
Laser830 Plus 45° Straight - bevel Edging
Intelligent laser edge banding machine
Twenty-four cells with a 45 degree saw, bevel and straight gluing, laser unit and bevel face trimming, 32 kW.
24 stations45° bevelLaser bonding32 kW
Read the specification
Put Laser800 against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.