Laser830
Intelligent laser edge banding machine
Three ways to bond on one frame: an EVA furnace, a two-colour PUR pot and a laser unit, so the machine can be quoted against whatever band the job specifies.
Overview
- Sixteen cells in the order printed on the sheet: 21.5-inch industrial computer, separating agent, pre-milling, gluing furnace, two-colour PUR pot, pressing, laser operating system, laser cooling system, pressing, head-and-tail trimming, rough and fine trimming, four-head tracking, double scraping, precise flat scraping, polishing head 1 and polishing head 2.
- An EVA gluing furnace and a two-colour PUR pot sit ahead of the laser unit, so EVA, PUR and laser band all run on the same bed.
- The laser unit is followed by its own cooling system, which keeps the head at working temperature through a shift.
- Panels from 40 mm wide and 9 to 60 mm thick, band 0.4 to 3 mm thick and 12 to 65 mm wide.
- 16 to 23 m/min on a 10,060 mm frame, 850 mm wide and 1,830 mm high, with 22.5 kW installed.
- Pressing runs before and after the laser, so the band is seated, activated and pressed again.
- Double scraping takes the trim marks off both edges, then precise flat scraping and two polishing heads finish the joint.
Laser830
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations16
Total power22.5 kW
Frame10,060 mm
Station sequence
Station 01 is the 21.5-inch computer, station 04 the EVA gluing furnace and station 07 the laser operating system; the sixteen cells follow the order printed on the sheet.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
EVA gluing furnace
The furnace melts EVA granulate and applies it to the panel face and the band in one pass; the pot sits on the machine, with no external tank and no cleaning solvent.
05
Two-colour PUR no-cleaning pot
The pot holds two PUR colours and switches between them without a solvent flush, and it sits outside the machine so the melt is kept apart from the EVA furnace.
06
Pressing
High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.
07
Laser operating system
The laser source, its power curve and the band feed are run from one controller, so a change of band is a recipe change rather than a re-setup.
08
Laser cooling system
A closed cooling circuit holds the laser at working temperature, so the bond stays even across a long shift.
09
Pressing
High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.
10
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
11
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
12
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
13
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
14
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
15
Polishing
Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.
16
Second polishing
A second pair of cotton wheels follows the first, for a higher sheen on the joint than one pass gives.
Technical data
| Model | Laser830 |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 16 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 22.5 kW |
| Machine size (L × W × H) | 10060 × 850 × 1830 mm |
Values from the Laser830 technical data sheet in the 2026 configuration list. The sheet prints the model as Laser830; the 45° build is a separate document and a separate page.
What the machine is built to do
- EVA, PUR and laser on one bedThree bonding paths in one station list: the machine is specified against the band, not the other way round.
- Cooling behind the laserA dedicated cooling system follows the laser unit, which is what a continuous run needs.
- Two polishing headsThe joint is finished twice, which is where a laser band reads against a lacquered panel.
- Double scrapingBoth edges of the band are scraped, so trim marks do not survive into the polish.
- Four-head trackingFour motors carry the tracking head and turn both corners.
- Eighteen-thirty height850 mm wide, 1,830 mm high: the bed is narrow enough for a single bay and tall enough for the tracking unit.
More from the 8 series
FM820JCDH
Skeleton-Line Grille Edge Bander
Skeleton-line doors, grille slats and standard straight edge banding on one track-fed 13-metre bed.
18 processing cells9–60 / 15–40 mmSkeleton lineTrack feed
Read the specification
Laser800
Intelligent laser edge banding machine
Fourteen cells on a 10.1 m frame: two-colour PUR pot, laser unit with cooling, four-head tracking and double polishing, at 22.5 kW.
14 stationsLaser bondingTwo-colour PUR22.5 kW
Read the specification
Laser830 Plus 45° Straight - bevel Edging
Intelligent laser edge banding machine
Twenty-four cells with a 45 degree saw, bevel and straight gluing, laser unit and bevel face trimming, 32 kW.
24 stations45° bevelLaser bonding32 kW
Read the specification
Put Laser830 against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.