Name: FM569JACD 45° Bevel and Straight Edge Bander
Brand: CNSK
SKU: FM569JACD

Overview

Seventeen numbered cells behind a crawler conveyor: separating agent, pre-milling, 45° saw, band grooving, bevel gluing, EVA pot, fast-melt tank, bevel and straight pressing, two-colour PUR pot, rough trimming, head-and-tail trimming, bevel and straight fine trimming, four-head tracking, straight and bevel scraping, flat scraping and double polishing.
The 45° saw cuts the square edge into a bevel in the same pass, and the changeover between bevel and straight is made on the screen rather than by changing a head.
Two glue systems on one frame: an EVA hot-melt pot with a fast-melt tank, and a two-colour PUR no-cleaning pot. The pot is chosen to the job, not to the machine.
Band grooving runs before the bevel is glued, so the band folds around the corner and the face contour stays crisp instead of splitting.
Four tracking heads, two at the leading end and two at the trailing end, follow the corner radius of the panel.
11,900 mm bed at 16 to 23 m/min. A full bevel-and-straight train on one frame, instead of a straight bander plus a second machine for the mitre.
Panel range quoted both ways: straight edge from 60 mm wide and 9 to 60 mm thick, 45° bevel from 80 mm wide and 15 to 40 mm thick; band 0.4 to 3 mm thick, 12 to 65 mm wide.

FM569JACD CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 / 15 – 40 mm

Stations17

Total power25 kW

Bed11,900 mm

Station sequence

The crawler conveyor feeds the panel; station 01 is the screen where the job is set, and seventeen numbered cells follow it.

01

17-inch industrial computer screen

Industrial-grade 17-inch screen with a graphical interface; parameters are entered by touch or input box and the effect of a change shows at once.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

45° saw cutting

One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.

05

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

06

Bevel gluing

A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.

07

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

08

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

09

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

10

PUR gluing

A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.

11

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

12

Head-and-tail trimming, bevel and straight

Both formats share one end-trimming head, so the changeover does not wait for a second cut.

13

Straight and bevel fine trimming

One trimming head takes the overhang off the straight face and the bevel face, bringing both flush with the panel.

14

Four-head corner tracking

Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.

15

Straight and bevel scraping

One scraping head serves both formats, so a changeover does not need a second setting.

16

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

17

Double polishing

Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.

Technical data

Model	FM569JACD
Feed rate	16 – 23 m/min
Panel width	≥ 60 / 80 mm (straight / 45° bevel)
Panel thickness	9 – 60 / 15 – 40 mm (straight / 45° bevel)
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Electric lift
Processing stations	17
Control screen	17-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	25 kW
Machine size (L × W × H)	11900 × 800 × 1750 mm

Values from the FM569JACD technical data sheet and the 2026 configuration list. Width and thickness are given as straight / 45° bevel: the saw sets both formats on the same machine.

What the machine is built to do

Seventeen stations, one passThe panel enters on the crawler conveyor and meets separating agent, pre-milling, the 45° saw, grooving, bevel gluing, the EVA pot, the fast-melt tank, bevel and straight pressing, the PUR pot, rough trimming, head-and-tail trimming, bevel and straight trimming, four-head tracking, scraping, flat scraping and double polishing in that order, without leaving the bed.
45° saw inside the lineThe mitre is cut on the machine rather than on a separate saw: the square edge and the flat face are milled into a 45° bevel in one pass, and the format is recalled from the screen.
EVA and PUR on the same frameA hot-melt pot with a fast-melt tank serves everyday EVA work; the two-colour PUR no-cleaning pot covers the jobs that have to hold in a wet or hot room. Both are on the machine, so the choice is made per order.
Grooving before gluingGrooves cut on the inner face of the band give it somewhere to fold, which is the difference between a bevel band that follows the corner and one that whitens along it.
Four-head trackingTwo heads work the leading end and two the trailing end, so the band is cut round the radius instead of square across it.
17-inch screenThe job is set on a 17-inch industrial computer: thickness, format and station parameters are entered by touch or input box, and a change shows its effect immediately.