Name: FM569JCD 45° Bevel and Straight Edge Bander
Brand: CNSK
SKU: FM569JCD

Overview

Seventeen numbered cells behind the crawler conveyor: separating agent, pre-milling, 45° saw, band grooving, bevel gluing, EVA pot, fast-melt tank, bevel and straight pressing, rough trimming, head-and-tail trimming, bevel and straight trimming, four-head tracking, straight and bevel scraping, flat scraping, cleaning and polishing.
Crawler pressing rather than a wheel beam: the panel is held over its full length, which is what keeps a 2.4 m door panel flat through the 45° saw.
10,820 mm bed, 16 to 23 m/min, 25 kW — shorter than the FM569JACD by a metre, with the same 45° saw, grooving and bevel gluing.
EVA hot-melt pot with a fast-melt tank as standard; PUR is quoted as a customization for shops that need it, rather than built in.
Four-head tracking and one scraping head that serves both the straight and the bevel format, so a changeover does not need a second setting.
Straight edge from 60 mm and 9 to 60 mm thick; 45° bevel from 80 mm and 15 to 40 mm thick.
The same frame can be specified with a mother-and-child saw unit: a second saw on the line, 35 kW in total and a 21.5-inch screen, for shops that cut and band in one pass.

FM569JCD CNSK · Dongguan

Feed rate16 – 23 m/min

Panel thickness9 – 60 / 15 – 40 mm

Stations17

Total power25 kW

Bed10,820 mm

Station sequence

Station 01 is the screen; seventeen numbered cells follow, with the 45° saw in fifth position.

01

17-inch industrial computer screen

Industrial-grade 17-inch screen with a graphical interface; parameters are entered by touch or input box and the effect of a change shows at once.

02

Separating agent

A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.

03

Pre-milling

Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.

04

45° saw cutting

One-key milling: the square edge is cut to 45° and the flat face milled into the bevel in the same pass.

05

Band grooving

Grooves are cut on the inner face of the band so it bends and presses cleanly around the corner.

06

Bevel gluing

A separate bevel gluing unit applies adhesive evenly, so the 45° band bonds without a visible line.

07

Gluing furnace

EVA glue pot; the melt is held at working temperature through the shift.

08

Fast-melt glue

The fast-melt unit brings the adhesive to working temperature in less time, so a cold start does not hold up the line.

09

Bevel and straight pressing

Pressure wheels load the bevel and the straight face together, so both bonds are made in one pass.

10

Rough trimming

The first trim brings the band's upper and lower edges down to the panel faces and leaves the allowance for the finishing head.

11

Head-and-tail trimming, bevel and straight

Both formats share one end-trimming head, so the changeover does not wait for a second cut.

12

Straight and bevel fine trimming

One trimming head takes the overhang off the straight face and the bevel face, bringing both flush with the panel.

13

Four-head corner tracking

Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.

14

Straight and bevel scraping

One scraping head serves both formats, so a changeover does not need a second setting.

15

Precise flat scraping

A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.

16

Cleaning

Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.

17

Polishing

Cotton polishing wheels clean the finished edge, leaving it smooth and even with the panel face.

Technical data

Model	FM569JCD
Feed rate	16 – 23 m/min
Panel width	≥ 60 / 80 mm (straight / 45° bevel)
Panel thickness	9 – 60 / 15 – 40 mm (straight / 45° bevel)
Edge band thickness	0.4 – 3 mm
Edge band width	12 – 65 mm
Pressure beam	Crawler pressing, electric lift
Processing stations	17
Control screen	17-inch industrial computer
Input voltage	380 V
Air pressure	0.7 MPa
Total power	25 kW
Machine size (L × W × H)	10820 × 800 × 1750 mm

Values from the FM569JCD crawler-machine technical data sheet and the 2026 configuration list. Width and thickness are given as straight / 45° bevel. The mother-and-child saw version is quoted separately at 35 kW, 21.5-inch screen and a 11,930 mm bed.

What the machine is built to do

Seventeen stations, straight and bevelPre-milling, the 45° saw, grooving, bevel gluing, the EVA pot, bevel and straight pressing, rough trimming, head-and-tail trimming, bevel and straight trimming, four-head tracking, scraping, flat scraping, cleaning and polishing run in one sequence on a 10,820 mm bed.
Crawler pressing over the full lengthA crawler belt carries and holds the panel rather than a row of wheels, so a long door panel stays flat and does not lift at the saw.
EVA standard, PUR on requestThe hot-melt pot with a fast-melt tank covers the ordinary job; PUR is specified as a customization where the joint has to survive heat or moisture.
Mother-and-child saw optionThe same machine can be built with a double-blade saw unit, quoted at 35 kW with a 21.5-inch screen, so cutting and banding happen on one line instead of two.
Four-head trackingTwo heads at each end follow the panel corner, so the band turns the radius instead of being cut square.
One scraping head, two formatsThe same scraper serves the straight face and the bevel face, which keeps the changeover to a screen setting.