FM669GJAZ
Narrow-Board Edge Bander, Four-Head Tracking
Four tracking heads, two at each end, are what make a narrow strip close on a finished corner: the FM669GJAZ is the 10 m build with that head set plus two glue systems.
Overview
- Sixteen numbered cells: separating agent, pre-milling, heat lamp 1, EVA furnace, pressing group 1, two-colour PUR pot, heat lamp 2, pressing group 2, head-and-tail trimming, rough and fine trimming, four-head tracking, double-edge scraping, precise flat scraping, cleaning and double polishing.
- Four tracking heads — two at the leading end and two at the trailing end — follow the corner radius of a 40 mm strip rather than cutting square across it.
- 10,040 mm frame, 950 mm wide bed, 1,880 mm high: longer than the compact machine, and wider than the standard 800 mm bed.
- Two heat lamps and two pressing groups, one pair either side of the EVA furnace and the PUR pot.
- 16 to 23 m/min, 22 kW, panels from 40 mm wide and 9 to 60 mm thick.
- Double-edge scraping and precise flat scraping behind the tracking heads, then cleaning and double polishing.
- 21.5-inch industrial computer as station 01.
FM669GJAZ
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations16
Total power22 kW
Bed10,040 mm
Station sequence
Station 01 is the 21.5-inch screen; four-head tracking is station 12.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
Gluing furnace
EVA glue pot; the melt is held at working temperature through the shift.
06
Pressing, first group
The first pressure group seats the band applied at the first glue station.
07
PUR gluing
A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.
08
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
09
Pressing, second group
A second pressure group follows the second glue station, for the band applied there.
10
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
11
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
12
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
13
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
14
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM669GJAZ |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 16 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 22 kW |
| Machine size (L × W × H) | 10040 × 950 × 1880 mm |
Values from the FM669GJAZ technical data sheet and the 2026 configuration list. The sheet header reads M669GJAZ; the model is FM669GJAZ.
What the machine is built to do
- Four-head tracking on a narrow stripTwo heads per end, so the band turns the corner radius at both ends instead of being cut square and trimmed back by hand.
- Two adhesives, two lamp-and-press pairsEVA furnace and two-colour PUR pot, each with its own heat lamp and pressing group.
- 950 mm bedWider than the standard narrow-board bed and 10,040 mm long, which is the build for shops that run long strips and wide-ish panels on one line.
- Double scraping, precise flat scrapingThe band and the glue film are taken by two scrapers, and the flat scraper cleans the face behind them.
- Annealed frame, milled tableFrame annealed before machining and table finish-milled, so the bed stays true over a long high-speed run.
- 21.5-inch screenThe recipe is recalled on the industrial computer rather than set station by station.
Edge samples
More from the 6 series
FM668GJAZ
Narrow-Board Edge Bander with PUR
10.1 m narrow-board line: two heat lamps, two pressing groups, EVA and two-colour PUR, 40 mm strips, 16 to 23 m/min.
16 stations40 mm narrow boardsEVA and PUR10.1 m bed
Read the specification
FM668JAZ
Compact Narrow-Board Edge Bander with PUR
Sixteen-station narrow-board line on a 9.3 m bed: two lamps, two pressing groups and a two-colour PUR pot, in a shorter bay.
16 stations40 mm narrow boards9.3 m bedEVA and PUR
Read the specification
FM668GJZ
Narrow-Board Edge Bander with Grooving
Fourteen stations on a 10.1 m heavy-frame bed: band grooving, one heat lamp and press group, 18.55 kW, strips from 40 mm.
14 stationsBand groovingHeavy pressure beam10.1 m bed
Read the specification
Put FM669GJAZ against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.