FM669GJZ
Narrow-Board Edge Bander with PUR
A short PUR line for narrow work: thirteen cells, four tracking heads and a double scraper, on a frame that fits where a 10 m bed does not.
Overview
- Thirteen numbered cells: separating agent, pre-milling, heat lamp, two-colour PUR pot, pressing, head-and-tail trimming, rough and fine trimming, four-head tracking, double-edge scraping, flexible flat scraping, cleaning and double polishing.
- The two-colour no-cleaning PUR pot is the only glue system: two adhesive colours, even dispensing, and cleaning without a solvent soak.
- Four tracking heads and a double scraper, so both ends of a 40 mm strip close on a finished corner before the scrapers take the band.
- 8,990 mm frame, 16 to 23 m/min, 18 kW, panels from 40 mm wide and 9 to 60 mm thick.
- One heat lamp and one pressing group, which is what keeps the station count at thirteen without dropping the finishing train.
- Flexible flat scraping takes residual hot-melt off the face, then cleaning and two polishing units.
- 21.5-inch industrial computer as station 01.
FM669GJZ
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations13
Total power18 kW
Bed8,990 mm
Station sequence
Station 01 is the 21.5-inch screen; thirteen numbered cells follow, with PUR gluing in fifth position.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
PUR gluing
A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.
06
Pressing
High-precision pressure wheels load the band evenly as it meets the panel, so the joint sits flat and holds.
07
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
08
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
09
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
10
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
11
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
12
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
13
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM669GJZ |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 13 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 18 kW |
| Machine size (L × W × H) | 8990 × 800 × 1900 mm |
Values from the FM669GJZ technical data sheet and the 2026 configuration list.
What the machine is built to do
- PUR on a short frameA two-colour no-cleaning pot on an 8,990 mm bed: the PUR joint without the 10 m footprint.
- Four-head tracking plus double scrapingBoth ends tracked, then two scraping heads, so the corner and the edge are finished in one pass.
- Thirteen cells, full finishing trainRough and fine trimming, tracking, scraping, flat scraping, cleaning and two polishers are all present; what is absent is the second lamp and press.
- Narrow-board bedAn 800 mm wide bed and an annealed frame, built for strips from 40 mm wide rather than for wide panels.
- Two polishing unitsThe finished edge is taken twice, which is visible on a dark band under raking light.
- 21.5-inch screenThirteen station parameters recalled from one screen.
More from the 6 series
FM668GJAZ
Narrow-Board Edge Bander with PUR
10.1 m narrow-board line: two heat lamps, two pressing groups, EVA and two-colour PUR, 40 mm strips, 16 to 23 m/min.
16 stations40 mm narrow boardsEVA and PUR10.1 m bed
Read the specification
FM668JAZ
Compact Narrow-Board Edge Bander with PUR
Sixteen-station narrow-board line on a 9.3 m bed: two lamps, two pressing groups and a two-colour PUR pot, in a shorter bay.
16 stations40 mm narrow boards9.3 m bedEVA and PUR
Read the specification
FM668GJZ
Narrow-Board Edge Bander with Grooving
Fourteen stations on a 10.1 m heavy-frame bed: band grooving, one heat lamp and press group, 18.55 kW, strips from 40 mm.
14 stationsBand groovingHeavy pressure beam10.1 m bed
Read the specification
Put FM669GJZ against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.