FM669JAZ
Narrow-Board Edge Bander, Fast-Melt PUR
One furnace with a fast-melt tank instead of two pots: the FM669JAZ brings EVA up to temperature in less time, then hands the job to a two-colour PUR pot when the order needs it.
Overview
- Sixteen numbered cells: separating agent, pre-milling, heat lamp 1, furnace with fast-melt tank, pressing group 1, two-colour PUR pot, heat lamp 2, pressing group 2, head-and-tail trimming, rough and fine trimming, four-head tracking, double-edge scraping, flexible flat scraping, cleaning and double polishing.
- A single gluing furnace with a fast-melt tank built into the station, which is why the sheet counts sixteen cells rather than seventeen.
- Two heat lamps and two pressing groups, one pair either side of the EVA furnace and the PUR pot.
- Four tracking heads and a double scraper, then a flexible flat scraper for the residual film.
- 10,030 mm frame, 900 mm wide bed, 16 to 23 m/min, 22 kW, panels from 40 mm wide and 9 to 60 mm thick.
- Annealed body and finish-milled table, sized for strips from 40 mm wide.
- 21.5-inch industrial computer as station 01.
FM669JAZ
CNSK · Dongguan
Feed rate16 – 23 m/min
Panel width≥ 40 mm
Stations16
Total power22 kW
Bed10,030 mm
Station sequence
Station 01 is the 21.5-inch screen; the furnace and its fast-melt tank are counted as one cell, so the sequence has sixteen numbered stations.
01
21.5-inch control screen
Industrial-grade 21.5-inch screen with a large graphical interface; parameters set by touch or input box, changes shown live.
02
Separating agent
A fine spray separates surplus glue from the panel face, so hot-melt does not mark the board after pressing.
03
Pre-milling
Two milling cutters re-finish the saw marks, burrs and out-of-square edges left by the panel saw, so the band seats on a clean face.
04
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
05
Gluing furnace with fast-melt tank
EVA pot with a fast-melt tank, so the adhesive reaches working temperature quickly and holds it through the shift.
06
Pressing, first group
The first pressure group seats the band applied at the first glue station.
07
PUR gluing
A no-cleaning PUR pot switches between two adhesive colours and dispenses evenly, for joints that have to hold and stay invisible.
08
Heat lamp
The board and the glue are pre-heated before pressing, which keeps the bond even in cold weather.
09
Pressing, second group
A second pressure group follows the second glue station, for the band applied there.
10
Head-and-tail trimming
The band is cut flush at the leading and trailing ends — quickly, and without ragged corners.
11
Rough and fine trimming
Rough trimming takes the bulk of the overhang and the fine head finishes to the panel face; the two cuts sit on one unit, so the band is not re-clamped between them.
12
Four-head corner tracking
Four driven heads round the corners at the leading and trailing ends, so the band follows the panel radius instead of cutting it square.
13
Double-edge scraping
Scraping on both edges of the run, for trim marks and surplus glue on either face.
14
Precise flat scraping
A flexible scraper takes surplus hot-melt off the panel face and the band, leaving the edge flat before polishing.
15
Cleaning
Residual hot-melt is diluted and isolated before polishing, so it lifts off instead of being smeared along the edge.
16
Double polishing
Two sets of cotton wheels finish the edge, for a higher sheen on the joint than a single head gives.
Technical data
| Model | FM669JAZ |
| Feed rate | 16 – 23 m/min |
| Panel width | ≥ 40 mm |
| Panel thickness | 9 – 60 mm |
| Edge band thickness | 0.4 – 3 mm |
| Edge band width | 12 – 65 mm |
| Pressure beam | Electric lift |
| Processing stations | 16 |
| Control screen | 21.5-inch industrial computer |
| Input voltage | 380 V |
| Air pressure | 0.7 MPa |
| Total power | 22 kW |
| Machine size (L × W × H) | 10030 × 900 × 1800 mm |
Values from the FM669JAZ technical data sheet and the 2026 configuration list. A second sheet for the same model quotes 10,950 × 1,050 × 1,800 mm; the build quoted here is the 10,030 mm frame.
What the machine is built to do
- Fast-melt inside the glue stationThe tank is built into the furnace cell, so the adhesive is brought up to temperature without a separate unit and a separate start-up wait.
- EVA and PUR on one frameThe furnace handles the everyday work and the two-colour PUR pot covers the joints that have to hold in heat or moisture.
- Four-head tracking, double scrapingBoth ends are tracked, and two scrapers take the band and the film before the flat scraper cleans the face.
- 10,030 mm bed, 900 mm wideA middle build: longer than the compact machine and wider than the 800 mm bed, for shops running strips and panels on the same line.
- Double polishingThe finished edge is taken by two polishing units after cleaning.
- 21.5-inch screenSixteen station parameters recalled from the industrial computer.
Edge samples
More from the 6 series
FM668GJAZ
Narrow-Board Edge Bander with PUR
10.1 m narrow-board line: two heat lamps, two pressing groups, EVA and two-colour PUR, 40 mm strips, 16 to 23 m/min.
16 stations40 mm narrow boardsEVA and PUR10.1 m bed
Read the specification
FM668JAZ
Compact Narrow-Board Edge Bander with PUR
Sixteen-station narrow-board line on a 9.3 m bed: two lamps, two pressing groups and a two-colour PUR pot, in a shorter bay.
16 stations40 mm narrow boards9.3 m bedEVA and PUR
Read the specification
FM668GJZ
Narrow-Board Edge Bander with Grooving
Fourteen stations on a 10.1 m heavy-frame bed: band grooving, one heat lamp and press group, 18.55 kW, strips from 40 mm.
14 stationsBand groovingHeavy pressure beam10.1 m bed
Read the specification
Put FM669JAZ against your panel.
Send the thickness, width and band you run. You get a station list, the tooling and a price against your name.